Start (wrench) here
Rotate
Install arm here
(see below for
details)
Arm Mounting Detail
Select angle of opening and use dimensions shown on
Page 4 and Dimension Chart below to locate 4 holes on
stop side of door for closer body
and 5 holes on stop and/or rabbet for Soffit
Plate. For applications not covered in these instructions, a
separate template will be required.
Prepare door and frame for fasteners. See “Preparation
for Fasteners”, Page 2.
or 213 dropplate, only if
required
Set closer power for door size using Power Adjustment
Chart below. Use 1/8” hex wrench supplied to adjust
Power Adjustment Shaft ... 15 turns maximum. Turn nut
to
to
power. See Page 6 for the illustration of this
step.
Install closer with
n
Note: If using cover, thread in
screws before mounting closer. Leave enough gap
between the head of the screw and the closer to slide the
cover on.
With door closed, use wrench to rotate pinion shaft as
illustrated below, see Arm Mounting Details.
CLOCKWISE
Increase, COUNTER-CLOCKWISE
Decrease
power adjustment screw toward
hi ge edge of door.
Caution:
Closer arm is under spring tension and may be
difficult to rotate.
Mount 213 Dropplate ... only if required (see Page 5).
Install Main Arm: Close valves -
and
, then turn pinion
shaft more than 50° to permit proper alignment of arm mark
with pinion flat -
for
hand door.
for
hand door.
See “Main Arm Installation Instructions” below.
(see page 6) before installing
cover ...
...
‘S’
‘L’
‘L’
Left
‘R’
Right
Make closer adjustments
CAUTION: Do not back valves out of closer
completely or a leak will result
use spacer blocks 293S or 891, if required.
.
Reopen valves by turning counter clockwise.
With door closed, align soffit plate with mounting holes in
frame. Fasten soffit plate to frame with flat head screws
provided.
Installation Instructions
Page 3
80-9350-2530-010 (06-09)
L
R
Y
S
Z
L
R
Y
S
Z
Pinion Flat
Left Hand Door
Typical Installation
Right Hand Door
Left Hand
Right Hand
Pinion Flat
“S” and “L”
Power Adjustment
Screw
BC
Valve
Stop
BC
Valve
Stop
Standard
and
Narrow
Frame
Flush
Partition
85°-
90°
10-3/8
(264)
8-3/8
(213)
9-3/8
(238)
10-1/2
(267)
8-3/8
(213)
9-3/8
(238)
9-5/8
(244)
7-5/8
(194)
8-5/8
(219)
9-3/4
(248)
7-5/8
(194)
8-5/8
(219)
9
(229)
7
(178)
8
(203)
9-1/8
(232)
7
(178)
8
(203)
8-3/8
(213)
6-3/8
(162)
7-3/8
(187)
8-1/2
(216)
6-3/8
(162)
7-3/8
(187)
PR50 /
PR150
Standard
and
Narrow
Frame
Flush
Partition
in.
(mm)
in.
(mm)
in.
(mm)
in.
(mm)
in.
(mm)
in.
(mm)
Up to
85°
90°-
95°
95°-
100°
100°-
105°
105°-
110°
110°-
130°
130°-
180°
6-1/8
(156)
4-1/8
(105)
5-1/8
(130)
6-1/4
(159)
4-1/8
(105)
5-1/8
(130)
11-1/8
(283)
9-1/8
(232)
10-1/8
(257)
11-1/4
(286)
9-1/8
(232)
10-1/8
(257)
9-5/8
(244)
7-5/8
(194)
8-5/8
(219)
9-3/4
(248)
7-5/8
(194)
8-5/8
(219)
8-1/8
(206)
6-1/8
(156)
7-1/8
(181)
8-1/4
(210)
6-1/8
(156)
7-1/8
(181)
7-3/4
(197)
5-3/4
(146)
6-3/4
(171)
7-7/8
(200)
5-3/4
(146)
6-3/4
(171)
Dim
A
B
C
A
B
C
Installation Dimensions Chart
5120
in.
(mm)
in.
(mm)
in.
(mm)
in.
(mm)
in.
(mm)
in.
(mm)
A
B
C
A
B
C
Power Adjustment Chart
DOOR
INT
EXT
PARALLEL ARM
INSTALLATION
MAXIMUM DOOR SIZE
34”
(0.85 m)
36”
(0.9 m)
40”
(1 m)
44”
(1.1 m)
48”
(1.2 m)
*18 -360° TURNS MAXIMUM AVAILABLE
*
FULL 360
TURNS
OF PO
WER ADJUSTMENT
SHAFT
o
NOT
RECOMMENDED
USE PR1601/CLP1601
PR51BF /
PR151BF /
5121BF
PR51 /
PR151 /
5121
2
8
3
5
2
9
5
7
3
12
7
10
4
5
10
14
13
16
INT
EXT
