3
network after powering on. Since performing a task in connecting network may consume some
power, it is required to follow the instructions to avoid draining battery of a ZigBee device
- Ensure your ZigBee network router or coordinator is powered on before inserting battery into the
ZigBee device.
- Ensure the ZigBee network router or coordinator is powered on and within range while a ZigBee
device is in use.
- Do not remove a ZigBee device from the ZigBee network router or coordinator without removing
the battery from a ZigBee device.
J
J
o
o
i
i
n
n
i
i
n
n
g
g
t
t
h
h
e
e
Z
Z
i
i
g
g
B
B
e
e
e
e
N
N
e
e
t
t
w
w
o
o
r
r
k
k
As a ZigBee device, the Keypad needs to join a ZigBee network to transmit and receive signal.
Please follow the steps below to join the device into the ZigBee network.
1.
Insert two
1.5V AA Lithium batteries
.
2.
Press and hold the OK key for 10 seconds for the Keypad to search and join an existing
ZigBee network. Please make sure to enable the permit-join feature on the router or
coordinator of your ZigBee network.
3.
After joining the ZigBee network, the Keypad will emit 2 beeps and it will be registered in the
security system in the network automatically. Please check the ZigBee network coordinator,
system control panel, or CIE (Control and Indicating Equipment) to confirm if joining and
registration is successful.
4.
The Keypad will not emit any sounds if it did not join the ZigBee network. Please check your
ZigBee network coordinator, control panel or CIE setting to ensure the permit-join function is
available, and then use the Factory Reset function below to join the ZigBee network.
F
F
a
a
c
c
t
t
o
o
r
r
y
y
R
R
e
e
s
s
e
e
t
t
If you want to remove the Keypad from the current network and join a new network, you need to
use the Factory Reset function to clear the Keypad for its stored setting and information first before
it can join another network. To perform Factory Reset:
1.
Press and hold the OK Key for 10 seconds, then release the button when the Keypad emits
1 beep and the LCD display shows a “KPT will reset in 2 seconds” message.
2.
The Keypad has been reset to factory default setting with all its previous network information
removed. It will now actively search for available ZigBee network again and join the network
automatically.
3.
If the Keypad successfully joins a ZigBee network, it will emit 2 beeps.
4.
If the Keypad cannot find an available ZigBee network, no sound will be emitted.
Installation
M
M
o
o
u
u
n
n
t
t
i
i
n
n
g
g
t
t
h
h
e
e
R
R
e
e
m
m
o
o
t
t
e
e
K
K
e
e
y
y
p
p
a
a
d
d
The Keypad is designed to be desktop mounted or wall mounted with fixing screws and plugs
provided.
For
desktop mounting
, simply place the Remote Keypad on a table/desk/bench etc.
Wall Mounting:
The bottom of the KP has 4 knockouts, where the plastic is thinner, for mounting purpose.
1.
Detach the base and cover assembly.
2.
Break through the plastic knockouts on the base.
3.
Drill 4 holes and fix the screws & plugs provided.
4.
Screw the base onto the wall.
5.
Reattach the base and cover assembly.
U
U
s
s
i
i
n
n
g
g
R
R
e
e
m
m
o
o
t
t
e
e
k
k
e
e
y
y
p
p
a
a
d
d
w
w
i
i
t
t
h
h
Z
Z
i
i
g
g
B
B
e
e
e
e
R
R
o
o
u
u
t
t
e
e
r
r
IMPORTANT NOTE
If the Remote keypad installation location is away from your system control panel and requires
ZigBee routers to improve signal strength.
DO NOT
use a ZigBee Router without backup battery. A
ZigBee router without battery will be powered down during AC power failure and the Remote
keypad connected to the router will lose connection with ZigBee network. You should plan your
Remote keypad installation location using only ZigBee router with backup battery.
