background image

engaged, the spacer and the brake shoes of the other
clutch are separated and are lubricated by cooling oil.
When inching pedal operates the inching valve, part of

or most of the oil flowing into clutch is drained to the oil
tank through inching valve, of the oil to torque
converter is the same as in neutral position.

1. OVERFLOW PRESSURE BUFFER VALVE

2. BUFFER VALVE

3. MAJOR OIL PRESSURE

4. MAJOR PRESSURE ADJUSTING VALVE

5. OVERFLOW VALVE

6. OVERFLOW PRESSURE

7. IMPELLER

8. GUIDE WHEEL

9. TURBINE

10. TO LUBRICATING OIL CIRCUIT

11. ROUGH OIL FILTER

12. OIL PUMP

13. INCHING VALVE

14. CLUTCH PRESSURE REDUCTION FINISHES

15. CLUTCH PRESSURE REDUCTION STARTS

16. ELECTROMAGNETIC REVERSING VALVE

17. THROTTLE ORFICE

18. FINE OIL FILTER

Figure 13. Transmission Hydraulic Schematic

SPEED REDUCER AND SPEED
DIFFERENTIAL
Speed Reducer

The speed reducer is located on the front of the
transmission case (see Figure 14). This mechanism
reduces the rotating speed of output shaft and
increased the torque transmitted from the output shaft.
It sends this torque to the speed differential. The
speed reducer is composed of a small spiral bevel
gear on the output shaft, a large spiral bevel gear, and
a small gear shaft. The large spiral bevel gear is
mounted on the small gear shaft through spline while
the two ends of small gear shaft are both supported

with tapered roller bearing, and a gasket is used to
adjust the clearance.

Hydraulic Transmission Case and Torque Converter

8000 YRM 2199

16

Содержание A7S1





































































































Отзывы: