Part #1030807 rev.C
41
• DO THIS FOR EACH CLIP.
• If clip moves, open cover and tighten
screw.
Close cover and check clip
again.
CLIP
SAFETY
CHECK
• Gold sliders should be an equal distance
from the slider marks on each tower
.
• IF the gold sliders are not equal
distances,
loosen or tighten screws until
sliders are equal.
F
INE
T
UNING
THE
T
OWER
TENSION
:
TO REMOVE RACK:
• Open tower covers & lift rack
up and off (do NOT
disassemble).
TO RE-INSTALL:
• Place Towers (covers open)
in original positions.
• Close Tower covers &
recheck rack and clips (Steps
11 & 12). Tighten if needed.
Other Information:
• SKS
®
Lock Cores
: Follow
directions and install with
Tower covers closed.
• To secure long loads
:
Use tie-downs at front
and rear of vehicle.
• Line front & back of clips
with
black vinyl liners;
trim if necessary.
• Slip lined clip
into Tower
through slits
on side.
I
NSTALL
C
LIPS
:
I
NSTALL
L
OCK
H
OLDER
& B
RASS
F
ASTENER
:
S
ECURE
THE
RACK
TO
BRACKETS
:
• Insert lock holder into holes in
Clip & Tower, matching notches.
• Push brass fastener
over lock
holder. It should feel snug.
• Repeat steps 7 & 8
for other
Tower.
INSTALL CLIPS AND SECURE RACK TO BRACKETS
– KEEP SLIDER MARKS EQUAL –
The gold sliders may
fall below or cover up
slider marks
depending on the
make of car.
NOTE:
The gold slider
should NEVER
TOUCH the
crossbar.
• PULL
each clip away from car—
PULL HARD!
ASSEMBLE TOWERS, END CAPS AND PADS ON BARS
• Lift Tower Hood & Crossbar
TOGETHER so that tower drops.
•
Insert wrench in hole.
• Turn wrench a short turn
clockwise—
this locks the Tower
to the bar.
Repeat
with other Tower.
L
OCK
T
OWERS
:
F
RONT
P
ADS
& E
NDCAPS
:
• Put 1 rubber base pad from clip
boxes
on base of each Tower.
• Put black
endcaps
on front bar.
Keep
Lock
Bar
Brass
Tower
SCREW
Cover
Q41Clip
B Pad
Black
Vinyl
SLIDER
TOWER HOOD
GOLD SLIDER
L
ABEL
:
Front Towers
with ”
front“
stickers.
TO BEGIN:
Loosen screws
on each tower turning
counter clockwise.
To Prepare:
• Clean
roof of car.
• Remove towers
from box.
• Remove bars
from plastic
holders.
• Open clip boxes
and plastic bag.
THIS CLIP INSTRUCTION
SUPERCEDES THE Q-TOWER
INSTRUCTIONS. FOLLOW THESE
INSTRUCTIONS ONLY!
Q41 clips can only be used with:
Bolt TopLoaders (Part #8005) or
PlusNut TopLoaders (Part #8006).
To verify that you are using Yakima
TopLoaders, call Customer Service
at 888/925-4621.
I
NSTALL
T
OWERS
TO
C
ROSSBAR
ON
FLAT
SURFACE
:
• Slide bar
into
tower, remove
wrench. REPEAT
for other tower.
• Turn wrench
counter
clockwise until it
stops.
• PULL tower hood UP
so
that wrench will engage
when inserted in hole.
Slide the loose Towers
along the bar until they
rest on top of the
brackets. The holes in
the rubber base pads
align with the bolt
heads of the brackets.
P
LACE
T
OWER
A
SSEMBLY
O
N
B
RACKETS
:
• Tighten one side slightly
so that cam
cover closes with light pressure—and
without moving the tower. Do not
overtighten.
Close cover.
• Go to opposite side,
tighten screw
slightly, close cover.
• Tighten each side as evenly as
possible
—a few turns on one tower,
then a few on the other. Open and
close cam covers with each
adjustment.
• Tighten until the covers close
firmly
—with some resistance.
This needs to be done gradually
to prevent the towers from
moving off center.
A
TTACH
R
EAR
R
ACK
AND
BAR
ASSEMBLY
:
R
EPEAT
S
TEPS
3
THROUGH
12
• REPEAT SAFETY CHECK in steps 11 & 12 .
SAFETY CHECK
PULL Clips, GRAB Bars
CHECK BOTH TOWERS:
• GRAB BAR on inside of Towers, push & pull
(use arm strength, full body strength not neces-
sary). Tower should not move.
• IF TOWERS MOVE, tighten screws slightly.
• KEEP SLIDER MARKS EQUAL.
• CLOSE COVER & CHECK AGAIN —
If towers move, check measurements again.
TOWER
SAFETY
CHECK
P
REPARATION
:
Q41
B