Yaesu FT-991A Скачать руководство пользователя

Страница: 29 / 158

Page 27

T-991

Operating Manual

Rear Panel

GND

Use this terminal to connect the transceiver to a good

earth ground, for safety and optimum performance.

Use a large diameter, short braided cable to make

the ground connections. For details on grounding the

transceiver, see “Grounding” on page 14.

ANT

Jack (144/430MHz)

This is the M-type (European version: N-type) co-

axial connector for the 144 MHz band and 430 MHz

band antennas (50 ohms).

RTTY/DATA

Jack

This is the input/output jack to connect a terminal

unit for RTTY and TNC for packet communications.

① DATA IN

② GND

③ PTT

④ SHIFT

⑤ DATA OUT

⑥ SQL

①

②

③

④

⑤

⑥

TUN/LIN

Jack

Connect the optional external antenna tuner “

FC-40

”

or the linear amplifier “

VL-1000

”.



+13V OUT



TX GND



GND



TX D (BAND A)



RX D (BAND B)



BAND C



RESET (BAND D)



TX INH

















GPS/CAT

Jack

This is the

RS-232C

jack for connecting a computer

or a commercially available external GPS device.

Connecting a computer to this jack, using a com-

mercially available

RS-232C

straight cable, enables

CAT control of the transceiver.

① DCD

② SERIAL OUT/RXD

　（GPS DATA IN）

③ SERIAL IN

④ DTR

⑤ GND

⑥ DSR

⑦ RTS

⑧ CTS

⑨ RI

①

②

③

④

⑤

⑧

⑨

⑦ ⑥

DC IN

Jack

This is the DC power supply connection for the

transceiver. Use the supplied DC cable to connect di-

rectly to a DC power supply, which must be capable

of supplying at least 23 A @13.8 VDC.

Содержание FT-991A































































































































































Результаты поиска

Содержание FT-991A

Отзывы:

Похожие инструкции для FT-991A

Бренды по названию

Популярные бренды

Yaesu FT-991A, Руководство по эксплуатации

Результаты поиска

Содержание FT-991A

Отзывы:

Похожие инструкции для FT-991A

Бренды по названию

Популярные бренды