Yaesu FT-818ND Скачать руководство пользователя страница 15

Страница: 15 / 76

Front Panel Control & Switches

key

Press the

key to activate

the receiver’s IF Noise Blank-

er.

AGC

Press the

key to select

the recovery time (

Fast

Slow

Auto

, or

Off

) for the

receiver’s AGC system.

–

No function

PWR

Press the

key to select

the transmitter power output

level (

Low 1

Low 2

Low 3

High

MTR

Press the

key to select

the display function of the

meter in the transmit mode

(Power, ALC, SWR, or MOD

indication).

–

No function

VOX

Press the

key to enable

the VOX (voice-operated

transmitter switching system)

in the SSB, AM, and FM

modes.

Press and hold in the

key for 1/2 second to recall

Menu #51 (for setting the

VOX Gain level).

Press the

key to activate

CW “Semi” Break-in opera-

tion.

Press and hold in the

key for 1/2 second to recall

Menu #17 (for setting the CW

Delay time). At a setting of 10

ms, operation emulates full

QSK performance.

KYR

Press the

key to activate

the built-in Electronic Keyer.

Press and hold in the

key for 1/2 second to recall

Menu #21 (for setting the

Keyer speed).

CHG

Press the

key to initiate

Battery Charging.

Press and hold in the

key for 1/2 second to recall

Menu #11 (for selecting the

Charging period).

VLT

Press the

key to display

the current battery voltage.

DSP

Press the

key to switch

the display between the

Large

Character and

Small

Charac-

ter modes.

TCH

Press the

key to initiate

Tone Search.

DCH

Press the

key to initiate

DCS Search.

–

No function

* The Operating Function number in this column does not appear on the LCD.

Display Icons

Operating Mode

PO:

AL:

S-Meter



TX Power Meter

ACL Meter

SW:

MO:

SWR Meter

Deviation Meter

Low Battery!

Split Frequency Operation

Low TX Power Selected

Automatic Power-Off

Digital Coded Squelch

CTCSS Decoder

CTCSS Encoder

Repeater Shift Direction

Dual Watch

Active (page 38)

(page 25)

Active (page 24)

Active (page 32)

Active (page 31)
Active (page 31)

(page 30)

Active (page 50)

LOCK Feature

Active (page 10)

FST Button MH-31

(

) Active

A8J

Rear Panel Antenna

Selected (page 54)



: This operation does not function in the FM Broadcast frequencies.

Содержание FT-818ND













































































Результаты поиска

Содержание FT-818ND

Отзывы:

Похожие инструкции для FT-818ND

Бренды по названию

Популярные бренды

Yaesu FT-818ND, Руководство по эксплуатации

Результаты поиска

Содержание FT-818ND

Отзывы:

Похожие инструкции для FT-818ND

Бренды по названию

Популярные бренды