Yaesu FT-2980E Скачать руководство пользователя страница 15

Страница: 15 / 80

Mobile Power Connections

To minimize voltage drop and avoid blowing the vehicle’s fuses, connect the supplied

DC power cable directly to the battery terminals. Do not attempt to defeat or bypass the

DC cable’s fuse - it is there to protect you, your transceiver, and your vehicle’s electrical

system.

Warning!

Never apply AC power to the power cable of the FT-2980R/E, nor DC voltage

greater than 15.8 Volts. When replacing the fuse, only use a 25-A (USA/Asian

version) or 20-A (European version) fuse. Failure to observe these safety

precautions will void the Limited Warranty on this product.



Use the transceiver only in a car with a negative ground 12 V DC system, where the

minus (-) pole of the battery is connected to the car body.



Do not connect the radio to the 24 V battery of a large vehicle.



Do not use a DC power cable other than the one that is supplied or specified.



High current is carried during transmissions; do not use the cigarette lighter connec-

tor inside the car as a power source.

High RF voltage is present in the TX RF section of the transceiver while transmit-

ting. Absolutely! Do not touch the TX RF section while transmitting.

Permanent damage can result when improper supply voltage, or reverse polarity

voltage, is applied to the FT-2980R/E. The Limited Warranty on this transceiver

does not cover damage caused by application of AC voltage, reverse polarity DC,

or DC voltage outside the specified range of 13.8 V ±15 %. When replacing fuses,

be certain to use a fuse of the proper rating.

The FT-2980R/E requires a 25 Amp (USA/Asian version) or 20 Amp (European

version) blade fuse.

FT-2980R/E

Fuse 25 A

Fuse 20 A

Fuse Holder

USA/Asian version

European version

WARNING!

NEVER remove the FUSE

holders from the DC cable.

RED: Positive (+)

BLACK: Negative (-)

Installation

FT-2980R/E Operating Manual

Содержание FT-2980E

















































































Результаты поиска

Содержание FT-2980E

Отзывы:

Похожие инструкции для FT-2980E

Бренды по названию

Популярные бренды

Yaesu FT-2980E, Руководство по эксплуатации

Результаты поиска

Содержание FT-2980E

Отзывы:

Похожие инструкции для FT-2980E

Бренды по названию

Популярные бренды