By changing the configuration of an internal DIP switch, the microprocessor in the FC-40 may be reset. Do this in the event
of erratic operation of the tuner, or to clear the tuner’s memories.
Cautions
Only connect cables to the FC-40 after switching the trans-
ceiver off.
If the FC-40 doesn’t tune even though you have pushed the
TUNER switch of the transceiver, it may be because the an-
tenna or its coaxial cable has a serious problem (very high or
low impedance due to “open” or “short”) or (the antenna ele-
ment is near 1/2 wavelength or multiple of the desired fre-
quency). Please check the antenna and coax if this happens.
Take appropriate measures to ensure that there is no possibil-
ity that someone may come in contact with the antenna or
FC-40 ANT terminal while your station is transmitting. Ob-
serve all practical and regulatory requirements for protecting
yourself and the public from the effects of radio frequency
radiation from your antenna system.
S1002
No.
Switch
1
OFF
2
OFF
S1003
No.
Switch
No.
Switch
1
OFF
5
ON
2
OFF
6
ON
3
OFF
7
OFF
4
OFF
8
OFF
D1002
4th Switch
Screw (5x20)
Earth Ground
Spring washers (SW6)
Mounting the FC-40
Microprocessor Resetting
Please note the default positions of the internal DIP switch
components. All switches, except for the 4th switch of S1003,
are for factory setup use only, and they should not be touched.
If you accidentally set a switch to the wrong position, please
refer to the table below to correct the situation.
“L” Wire Monopole
Ground to Engine Block/Keel
GND Lug
Ship Mobile
Car Mobile
Ground to Engine/Chassis
Washer (FW6)
Nut (N6)
The mounting method for the FC-40 is determined by the antenna type and station location. In all installations, however, the FC-40 must
be located at the intended feedpoint for the antenna. The drawings below show examples of placement of the FC-40 in typical mounting
locations. Following are several important considerations to bear in mind during installation:
The side of the FC-40 with the cables extruding is oriented
downward (to minimize the chance of water leakage through
the cable holes).
The grounding wire (for monopoles) and part(s) of the an-
tenna wire between the tuner terminals and the nearest an-
tenna support should be as short as possible.
The antenna must not touch anything except supporting insu-
lators.
If there is any chance of stress on the cables to the trans-
ceiver, they should be supported independently, with a slack
loop between their support and the FC-40.
For base stations, the FC-40 may be mounted either on a flat sur-
face such as the wooden board shown in Figure 1, or a 2.16” - 2.55”
(55-65 mm) mast, using the supplied U-bolt kit shown in Figure 2.
For mobile installations, the FC-40 should be bolted to a flat sur-
face using either bolts or self-tapping screws (Figure 3) inside the
trunk or cabin, as close to the base of the antenna as possible. Note
that it can be mounted horizontally if well protected from the weather.
After mounting the FC-40, connect the cables from the FC-40 to
the ANT and TUNER (or CAT/LINEAR) jacks (depends on the
transceiver) on the rear panel of the transceiver. Refer to the
transceiver’s Operating Manual for details of the interconnec-
tions with the transceiver. If you use the FC-40 with the Yaesu
FT-857D/-897D transceiver, refer to the instructions on the op-
posite page of this manual for interconnection details.
Figure 3
Figure 2
Figure 1
Washer (FW5)
Outer washer (OW5)
Nut (N5)
Nut (N5)
Screw (M5x20)
Outer washer (OW5)
Washer (FW5)
Clearing Memory
1. Turn “off” the transceiver.
2. Remove the 8 screws affixing the case of the FC-40, then
remove the case.
3. Turn the 4th switch of S1003 to “on”.
4. Turn on the transceiver.
5. D1002 will glow green briefly, then turn off. This con-
firms the resetting of the microprocessor.
6. Return the 4th switch of S1003 to “off” .
7. Turn “off” the transceiver again.
8.
Replace the case, using the 8 screws removed in step (2)
above.
Screw (5x20)
Washer (FW5)
Outer washer (OW5)
Please see your transceiver’s Operating Manual for operation with the FC-40 Tuner.
See the instructions at the right side of this page for operation of the FC-40 with FT-857/-897 transceivers.
Tuner Operation
FT-857D/-897D Tuner Operation
FUNC
A
DIAL
SELECT
FT-897D
FT-857D
1. Press and hold in the
F
(
FUNC
) key for one second to
activate the Menu mode.
2. Rotate the
MEM/VFO CH
(FT-857D:
SELECT
) knob to re-
call Menu Mode
No-001
No-001
No-001
No-001
No-001 [EXT MENU
EXT MENU
EXT MENU
EXT MENU
EXT MENU]
, then rotate the
DIAL
to change the setting to “
ON
ON
ON
ON
ON
” to enable the extended Menu
Mode.
3. Rotate the
MEM/VFO CH
(FT-857D:
SELECT
) knob to re-
call Menu Mode
No-020
No-020
No-020
No-020
No-020 [CAT
CAT
CAT
CAT
CAT
/
LIN
LIN
LIN
LIN
LIN
/
TUN
TUN
TUN
TUN
TUN]
. The default set-
ting for this Menu is “
CAT
CAT
CAT
CAT
CAT
.” Rotate the
DIAL
to change the
setting to “
TUNER
TUNER
TUNER
TUNER
TUNER
.”
4. Press and hold in the
F
(
FUNC
) key for one second to
save the new setting and exit, then turn the transceiver off.
5. Set up the
FC-40
and
FT-897D/-857D
per the illustration
on the opposite page of this manual, then turn on the
transceiver’s power again.
Do not set up the FC-40 and
FT-897D/-857D before changing the Menu Mode,
item No-020
[
CAT/LIN/TUN
].
6. Press and hold in the
F
(
FUNC
) key for one second to
activate the Menu mode.
7. Rotate the
MEM/VFO CH
(FT-857D:
SELECT
) knob to recall
Menu Mode
No-085
No-085
No-085
No-085
No-085 [TUNER
TUNER
TUNER
TUNER
TUNER
/
ATAS
ATAS
ATAS
ATAS
ATAS]
. The default setting for
this Menu is “
OFF
OFF
OFF
OFF
OFF
.” Rotate the
DIAL
to change the setting to
“
TUNER
TUNER
TUNER
TUNER
TUNER
.”
8. Press and hold in the
F
(
FUNC
) key for one second to
save the new setting and exit.
9. Press the
F
(
FUNC
) key, as needed, to recall Multi Func-
tion Row “k” [
TUNE
TUNE
TUNE
TUNE
TUNE
,
DOWN
DOWN
DOWN
DOWN
DOWN
,
UP
UP
UP
UP
UP
].
10. Press the [
A
](
TUNE
TUNE
TUNE
TUNE
TUNE
) key to turn the
FC-40
on. “Parenthe-
ses” will appear on both sides of the “
TUNE
TUNE
TUNE
TUNE
TUNE
” indication, and
“
TUNR
” will appear on the LCD.
I
MPORTANT
!
The
FC-40
, working in concert with the
FT-897D/-857D
trans-
ceiver, can store impedance matching data in its micro-computer
memory, so as to provide instant adjustment as you transmit in
different areas of a particular band. A total of 200 memories are
provided, with the capability to resolve new tuning data every
10 kHz. A few guidelines should be noted regarding the
FC-
40
’s memory system:
Tuning data is stored when you make an active effort to store it
by pressing and holding in the [
A
](
TUNE
TUNE
TUNE
TUNE
TUNE
) key for one second.
Although the tuner will automatically activate itself if it encoun-
ters more than 2:1 SWR, this memory will not be stored unless
you have pressed the [
A
](
TUNE
TUNE
TUNE
TUNE
TUNE
) key for one second. This al-
lows you to store your favorite operating frequency areas into
tuner memory without tying up memory space with matching
data on seldom-used frequencies.
If the
FC-40
cannot resolve a satisfactory match because the
SWR is above 2:1), the tuning process will stop, and no memory
data will be stored. However, you may wish to move frequency
a few kHz, then press the [
A
](
TUNE
TUNE
TUNE
TUNE
TUNE
) key again for one second,
as slight changes in the reactance may allow a match to be ob-
tained. Then go back to the original frequency and try again.
If the impedance encountered by the
FC-40
exceeds 2:1, and
the “HSWR” icon is illuminated, the microprocessor will not
retain the tuning data for that frequency, as the
FC-40
presumes
that you will want to adjust or repair your antenna system so as
to correct the high SWR condition.
BAT T-B
BAT T-A
MEM/VFO CH
DIAL
F
A
11. Press and hold in the [
A
](
TUNE
TUNE
TUNE
TUNE
TUNE
) key to initiate automatic
tuning. The
FT-897D/-857D
transmitter will be activated,
a carrier signal will be sent out, and the coils and capacitors
in the
FC-40
will be selected/adjusted for optimum SWR.
When tuning is complete, the transmission will cease, and
you will be ready for operation on this frequency.
Tuning data will be stored in the FC-40’s Memory
system. See the discussion below for details on how
this works.
If using the FC-40 with the FT-897D under internal
battery (FNB-78) power, the FC-40 may not operate
properly if the battery voltage is low.
FT-897D
FT-857D
“
TUNR
”
“
TUNR
”
