Xylem Sontek River Surveyor RS5 Скачать руководство пользователя страница 92

Страница: 92 / 149

SonTek RS5 User Manual (August 2020) 92

Any Edge settings from the Smart Page (described in Section 7.6), and any

modifications to these settings can be made here. The distance to bank can be either

measured or estimated. Click

to begin the Start Edge data collection.

The Edge data collection tab will appear, as shown in Figure 73. Keep the RS5 as

stationary as possible during the edge data collection. It is recommended that the user

collect at least 10 good samples with at least 2 vertical cells during the edge

measurement. If the user selected to use the auto-edge feature, the RSQ software will

automatically switch to measuring the Transect after that number of samples is done.

Alternatively, when the Edge measurement is satisfactory, the user can manually

proceed to the Transect measurement.

Figure 73. Start Edge Data Collection Dialog

7.10.5 Transect Section

If proceeding to the Transect measurement manually, click the Next: Transect Section

button (or use [F5]), highlighted in Figure 74.

Содержание Sontek River Surveyor RS5






















































































































































Результаты поиска

Содержание Sontek River Surveyor RS5

Отзывы:

Похожие инструкции для Sontek River Surveyor RS5

Бренды по названию

Популярные бренды

Xylem Sontek River Surveyor RS5, Руководство пользователя

Результаты поиска

Содержание Sontek River Surveyor RS5

Отзывы:

Похожие инструкции для Sontek River Surveyor RS5

Бренды по названию

Популярные бренды