Xylem sensus AutoRead Скачать руководство пользователя

Страница: 42 / 161

Updating HHD Note Codes does not affect Vehicle Protocol Note Codes. If changes are

made to HHD Notes, they will not affect Vehicle Protocol Note Codes.

Vehicle Device Parameters

Individual device parameters for Vehicle Transceiver Units (VXUs) can be set or changed

on the

Device Control

screen in the Vehicle protocol. This screen can be accessed by

clicking the specific device number in the Tree View on the left side of the screen, or by

double clicking the desired device in the list of devices on the

Polling Devices

screen. As in

Handheld protocol, changes can only be made when there are no routes or meters loaded

to the device being viewed.
•

Delete Route File after Retrieve

: This setting causes AutoVu to delete the route file

from the route disk after the meter reader retrieves the route into AutoVu. This setting is

available for two reasons: it helps conserve disk space when using 3 ½" floppy disks,

and also prevents the meter reader from inadvertently re-retrieving the route and thus

losing any collected readings from the VXU. In most cases, it is not necessary to use this

setting.

•

Increment Read Count on Notecodes

: This setting will allow note code entries to

count as readings on the read counter in AutoVu and AutoRead. It also will cause the

software to consider a meter with a note entry as a read meter, even though no meter

reading was taken.

•

Increment Read Count on High/Low Violations

: This setting causes AutoVu to

automatically "accept" readings that are not within the expected read range set by billing.

In most cases, this setting should be used (checked) if readings that are higher or lower

than expected are desired by the utility. If this setting is not checked, the meter reader

will have to manually "accept" the High and Low readings in the AutoVu application, and

the reading counter will not reflect the High and Low readings in the Read Counter.

•

Automatically Export on Exit

: This setting determines whether or not the AutoVu

software will automatically prompt the meter reader to save the readings when they close

the software. It is recommended that this setting be left checked.

•

Beep on Interrogate

: This setting will cause the AutoVu software to beep each time an

interrogation (or wakeup) message is transmitted by the Vehicle Transceiver Unit (VXU).

•

Beep on Warnings

: When enabled, will cause the AutoVu software to beep each time a

warning message is encountered for a meter.

•

Beep on High/Low Violations

: This will cause the AutoVu software to beep each time a

reading that is not within the High/Low limits specified by the billing software is collected

by the VXU.

3 Polling Devices | 42

Содержание sensus AutoRead


































































































































































Результаты поиска

Содержание sensus AutoRead

Отзывы:

Похожие инструкции для sensus AutoRead

Бренды по названию

Популярные бренды

Xylem sensus AutoRead, Руководство пользователя

Результаты поиска

Содержание sensus AutoRead

Отзывы:

Похожие инструкции для sensus AutoRead

Бренды по названию

Популярные бренды