Xylem sensus AutoRead Скачать руководство пользователя

Страница: 30 / 161

12345678

is automatically entered on that account (where 12345678 is the actual ID of

the meter read). This information will then print out on the AutoRead Route Note report

providing for easy correction of these accounts in billing.Please refer to

Table 3-1

for

more scenarios.

Possible Scenarios

"Prompt when

not matching

displayed

location"

"Prompt when

not found on

route"

Result when reading a meter whose ID doesn't

match

Unchecked

The HHD will automatically search the route for that

Meter ID and a message stating Not at displayed

location or Meter not on route! will appear momentarily.

No user input is available.

Checked

Unchecked

The user is prompted to either search the route for that

Meter ID or apply the reading to the current location.

Unchecked

Checked

The HHD will automatically search the route for that

Meter ID and if not found, will prompt the user to either

store that reading as a non-route meter or apply the

reading to the current location.

Checked

The user will first be prompted to either search the

route for that Meter ID or apply the reading to the

current location. If

is selected and the Meter

ID cannot be found on the route, an additional prompt

will appear to either store that reading as a non-route

meter or apply the reading to the current location.

If none of these options are enabled, the model AR5000 HHD will react in the same

fashion as the AR4000 model.

1. These check boxes are identical to their counter-parts on the AR400X tab. Please refer

to numbers 27-31 for explanations of each parameter.

User-defined Function Keys

: For commonly used route functions such as adding

notes and manual reads, performing route searches, etc; the AR5000 series HHDs

use function buttons labeled F1-F12 (located at the top of the keypad on the HHD).

These may be configured according to user preference by using the drop-down boxes

located beside each Function number, or restored to default settings using the

Restore

Defaults

button. The following options are available:

• <none>
• Manual Read
• Note
• Search
• Mark
• Transaction History
• Configuration
• Gun Utilities
• Display Route Name
• Add New Meter
• Radio Read
• Work Order
• Interval Data

3 Polling Devices | 30

Содержание sensus AutoRead


































































































































































Результаты поиска

Содержание sensus AutoRead

Отзывы:

Похожие инструкции для sensus AutoRead

Бренды по названию

Популярные бренды

Xylem sensus AutoRead, Руководство пользователя

Результаты поиска

Содержание sensus AutoRead

Отзывы:

Похожие инструкции для sensus AutoRead

Бренды по названию

Популярные бренды