Xylem sensus AutoRead Скачать руководство пользователя

Страница: 123 / 161

return to the proper location, a Search can be performed for Unread Meters or for the

address of the next location, or if a Touch Pad is at the next location it can be read and

when the

Not at Displayed Location

message is encountered you can press

Shift

Last

, and

IT's4you2

then

followed by the

PageDown

key to return to the

next location on the route.

Corrections with AR500X Equipment

The AR5000 series HHDs have additional features to aid in the troubleshooting of incorrect

meter ID's. While based on the same concepts above, these features greatly simplify the

process. Please refer to Section

3.4

- The

AR500x

Tab for more information on how to take

advantage of these options.
These options are turned off by default which causes the 5000 HHD to mimic the 4000;

so if you prefer, you may follow the above steps for the AR400x equipment and simply

substitute the

key on the 5000 HHD in place of the

Shift

Last

combo on the 4000, the

key in place of the

button, and the

Right

tab key in place of

PageDown

RadioRead Meters

Corrections with AR400x or AR500x Equipment

No Response from Device (Message on HHD)

On a RadioRead account a

No Response from Device

message indicates that the

MXU did not communicate and more troubleshooting is required. A note indicating this

should be entered as well as a Manual reading. If using a HHD with an MXU programmer

loaded, then programming should be attempted, and if successful, the reading tried again. If

the MXU ID, Class, or Password are incorrect, or the MXU has not been properly activated,

it will not respond. See the RadioRead MXU Troubleshooting Guide included with this

manual for more troubleshooting tips on MXUs.

ID Not on Route (Message on HHD)

The procedures to troubleshoot this error when performing a RadioRead are identical to

those listed above for TouchReads. Please refer to those steps with the only difference

being that you will perform a Radio Interrogation on an MXU in place of a TouchRead on a

TouchPad.

Not at Displayed Location (Message on HHD)

The procedures to troubleshoot this error when performing a RadioRead are identical to

those listed above for TouchReads. Please refer to those steps with the only difference

being that you will perform a Radio Interrogation on an MXU in place of a TouchRead on a

TouchPad.

10 Troubleshooting Non-Route Meter IDs | 123

Содержание sensus AutoRead


































































































































































Результаты поиска

Содержание sensus AutoRead

Отзывы:

Похожие инструкции для sensus AutoRead

Бренды по названию

Популярные бренды

Xylem sensus AutoRead, Руководство пользователя

Результаты поиска

Содержание sensus AutoRead

Отзывы:

Похожие инструкции для sensus AutoRead

Бренды по названию

Популярные бренды