Xylem sensus AutoRead Скачать руководство пользователя

Страница: 12 / 161

System Requirements

Component

Requirement

Operating System:

Windows XP Professional, Vista Business, Vista Enterprise, or Vista Ultimate

(32-bit versions only), and Windows 7, 8 & 10 Professional (32 and 64-bit

versions.)

Processor:

2.4 GHz Processor

Memory Requirements:

2 GB RAM

Communications Port:

Legacy Charging stand: 1 Serial Port or 1 USB Port

(A USB to Serial adapter

is needed if an on-board serial port is unavailable. The IOGear GUC232A is

recommended.)

CD-ROM Drive:

Required only if you are using a CD to install the AutoRead software.

Suggestions to Optimize AutoRead Performance and Benefits

The AutoRead reports use True Type™ fonts by default. Many dot matrix, or "line" printers,

have difficulty reproducing these fonts, or print them much more slowly than they would

print a draft font type. As a result, users may find that a Laser or Ink Jet printer works best

when printing the AutoRead meter reading reports. The printer used for AutoRead reports

has no effect on the printer used for printing bills.
It is possible to set up AutoRead to print to any printer that is installed on the PC, as long

as it is set up as an available printer within the Windows operating system. If a dot matrix or

"line" printer is chosen to print AutoRead reports, users may find that setting the Windows

printer properties for the dot matrix printer to "Draft" mode will speed the printing of the

AutoRead reports.

Suggested System Precautions

All computer equipment and peripherals, including HHD charging stands, should be

connected to an uninterruptible power source (UPS). This will greatly reduce the chances

of lost data due to general power outages. In addition, most UPS units are equipped with

power-surge protectors that can prevent damage to the system components from sudden

power surges. Make sure that the UPS selected has ample capacity to power the system

for which it is employed.
If the utility uses Sensus Metering Systems PhonRead Meter Reading System, Call-In

Protocol, or if it is connected to an external billing system via phone modem, a surge

protector for the phone line should also be considered. While the voltage carried by the

typical phone line is very low, in the case of a lightning strike in the general vicinity, current

transmitted along the phone line can be substantial and can cause damage to sensitive

system components.
Information about the UPS, and both types of surge protectors, can be obtained from most

computer retailers.

User Prerequisites

This manual presumes a basic, working knowledge of Windows operating system

operations. Users should have previous experience operating a PC running a Windows

(see

Table 2-3

) Operating System. For individuals not familiar with these operating systems,

formal instruction is strongly recommended.

2 Before Using AutoRead | 12

Содержание sensus AutoRead


































































































































































Результаты поиска

Содержание sensus AutoRead

Отзывы:

Похожие инструкции для sensus AutoRead

Бренды по названию

Популярные бренды

Xylem sensus AutoRead, Руководство пользователя

Результаты поиска

Содержание sensus AutoRead

Отзывы:

Похожие инструкции для sensus AutoRead

Бренды по названию

Популярные бренды