Xylem Flygt 2620.172 Скачать руководство пользователя страница 25

Страница: 25 / 72

If there is a question regarding the tightening torques, then contact a sales or authorized
service representative.

Screws and nuts

Table 1: Stainless steel, A2 and A4, torque Nm (ft-lbs)

Property

class

M10

M12

M16

M20

M24

M30

1.0 (0.74)

2.0 (1.5)

3.0 (2.2)

8.0 (5.9)

15 (11)

27 (20)

65 (48)

127 (93.7) 220 (162) 434 (320)

70, 80

2.7 (2)

5.4 (4)

9.0 (6.6)

22 (16)

44 (32)

76 (56)

187 (138) 364 (268) 629 (464) 1240 (915)

100

4.1 (3)

8.1 (6)

14 (10)

34 (25)

66 (49)

115 (84.8) 248 (183) 481 (355) —

—

Table 2: Steel, torque Nm (ft-lbs)

Property

class

M10

M12

M16

M20

M24

M30

8.8

2.9 (2.1)

5.7 (4.2)

9.8 (7.2)

24 (18)

47 (35)

81(60)

194 (143) 385 (285) 665 (490) 1310

(966.2)

10.9

4.0 (2.9)

8.1 (6)

14 (10)

33 (24)

65 (48)

114 (84)

277 (204) 541 (399) 935 (689) 1840

(1357)

12.9

4.9 (3.6)

9.7 (7.2)

17 (13)

40 (30)

79 (58)

136 (100) 333 (245) 649 (480) 1120

(825.1)

2210

(1630)

Hexagon screws with countersunk heads

For hexagon socket head screws with countersunk head, maximum torque for all property
classes must be 80% of the values for property class 8.8 above.

4.4 Change the oil

A paraffin oil with viscosity close to ISO VG32 is recommended. The pump is delivered
from the factory with this type of oil. Examples of suitable oil types are the following:

• Statoil MedicWay 32

™

• BP Enerpar M 004

™

• Shell Ondina 927

™

• Shell Ondina X430

™

In applications where poisonous properties are of less concern, a mineral oil with viscosity
up to ISO VG32 can be used.

WS006203A

1. Inspection screw

2. Oil screw

Figure 6: Symbols

Empty the oil

1. Lay the pump on its side.

Lock the pump with supports to prevent it from rolling over.

2. Remove the oil screw.

4 Maintenance

2620.172/.281 Service and Repair Instructions

Содержание Flygt 2620.172









































































Результаты поиска

Содержание Flygt 2620.172

Отзывы:

Похожие инструкции для Flygt 2620.172

Бренды по названию

Популярные бренды

Xylem Flygt 2620.172, Инструкции по обслуживанию и ремонту

Результаты поиска

Содержание Flygt 2620.172

Отзывы:

Похожие инструкции для Flygt 2620.172

Бренды по названию

Популярные бренды