manualshive.com logo in svg

Xylem Bell & Gossett e-80SC Series, Инструкция по эксплуатации

Поделиться
Скачать
Xylem Bell & Gossett e-80SC Series Скачать руководство пользователя страница 14

Check

Explanation/comment

Checked

Check that the suction or discharge lines are not

forced into position.

Coupling and bearing wear will result if suction

or discharge lines are forced into position.
The code for Pressure Piping (A.S.A.B. 31.1) lists

many types of supports available for various

applications.

Check that fittings for absorbing expansion are

installed in the system when considerable

temperature changes are expected.

This helps to avoid strain on the pump.

Check that you have a foot valve of equal or greater

area than the pump suction piping when you use in

an open system with a suction lift.

Prevent clogging by using a strainer at the

suction inlet next to the foot valve. Make sure

that the strainer has an area three times that of

the suction pipe with a mesh hole diameter of

no less than 0.25 in. (0.64 cm).

Check that flexible piping is used on both the suction

and discharge sides of the pump when you use an

isolation base.

—

Check that a B&G Triple Duty

®

 valve is installed in the

discharge line.

This valve serves as a check valve that protects

the pump from water hammer, and serves as an

isolation valve for servicing and for throttling.

Check that the pipeline has isolation valves around

the pump and has a drain valve in the suction pipe.

—

4.2  Typical pump installation

Various installation arrangements can be used as described below.
Series e-80SC pumps can be installed directly in the piping with pipe hangers adequate
to carry the loads from the pump and piping.

Figure 4

In many installations, the piping is installed near the ceiling with the pump located close
to the floor for ease of maintenance. Pumps with up to 4 inch nozzles and up to 286
NEMA (180 IEC) frame motors can be installed in this configuration with pipe hangers
adequate to carry the loads from the pump, piping and piping accessories. Larger pumps
can be installed in this configuration but require either the optional B&G Flange Supports
or a floor support under the discharge elbow and an adjustable support leg under the
B&G Suction Diffusor Plus.

4  Installation

12

Series e-80SC INSTRUCTION MANUAL

Содержание Bell & Gossett e-80SC Series

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды