background image

P91 Lead Acid 2U User’s Manual 

 

               Uninterruptible Power Supply 

Xtreme Power Conversion Corporation 

 

Page 30 

 

8. Xtreme Power Conversion Limited Warranty 

 

 
Xtreme Power Conversion (XPC) Corporation warrants Xtreme Power Conversion equipment, when properly 
applied and operated within specified conditions, against  faulty materials or workmanship for a period of 

three years for P91-Series products 

from the date of purchase. XPC Corporation warrants 

internal batteries 

for a period of three years 

from the date of purchase. For equipment sites within the United States and 

Canada, this warranty covers repair or replacement, at the sole discretion of XPC Corporation. The customer is 
responsible for the costs of shipping the defective product to XPC Corporation. XPC Corporation will pay for 
ground shipment of the repaired or replacement product. This warranty applies only to the original purchaser.   

 

If equipment provided by XPC Corporation is found to be 

Dead-on-Arrival (DOA)

, XPC Corporation will be 

responsible for the costs of shipping product to and returning equipment from the customer in a timely 
manner as agreed to with the customer, once the customer has requested and received a 

Return Material 

Authorization (RMA) 

number. DOA equipment is defined as equipment that does not properly function 

according to user documentation when initially received and connected in conjunction with proper procedures 
as shown in the user documentation or via support provided by XPC Corporation personnel or authorized 
agents.   

 

This warranty shall be void if (a) the equipment is repaired or modified by anyone other than XPC Corporation 

or a XPC Corporation approved third party; (b) the equipment is damaged by the customer, is improperly used 

or stored, is subjected to an adverse operating environment, or is operated outside the limits of its electrical 
specifi

cations;  or  (c)  the  equipment  has  been  used  or  stored  in  a  manner  contrary  to  the  equipment’s 

operating manual, intended use or other written instructions. Any technical advice furnished by XPC 
Corporation or a XPC Corporation authorized representative before or after delivery with regard to the use or 
application of Xtreme Power Conversion equipment is furnished on the basis that it represents XPC 
Corporations best judgment under the situation and circumstances, but it is used at the recipient’s sole risk.   

 

EXCEPT AS STATED ABOVE, XPC Corporation DISCLAIMS ALL WARRANTIES, EXPRESSED OR IMPLIED, 
INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.   

 

EXCEPT AS STATED ABOVE, IN NO EVENT WILL XPC Corporation BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, 
INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF Xtreme Power Conversion 
EQUIPMENT, including but not limited to, any costs, lost profits or revenue, loss of equipment, loss of use of 
equipment, loss of software, loss of data, cost of substitutes, or claims by third parties. Purchaser’s sole and 
exclusive remedy for breach of any warranty, expressed or implied, concerning Xtreme Power Conversion 
equipment, and the only obligation of XPC Corporation under this warranty, shall be the repair or replacement 

of defective equipment, components, or parts; or, at XPC Corporations sole discretion, refund of the purchase 

price or substitution of an equivalent replacement product.

 

 

 

 

 

Содержание P91-1000





































Отзывы: