manualshive.com logo in svg

Xtreme P90L-1500, Руководство пользователя и инструкция по установке

Поделиться
Скачать
Xtreme P90L-1500 Скачать руководство пользователя страница 5

Xtreme Power Conversion Corporation

P90L 1500–3000 User’s Manual

Page 5

Uninterruptible Power Supply

For additional safety instructions, please use the Safety Manual as a reference.

Special Symbols

The following symbols used on the UPS warn you of precautions:

RISK OF ELECTRIC SHOCK - Please observe the warning that a risk of electric shock is present

CAUTION: REFER TO OPERATOR’S MANUAL - Refer to the operator’s manual for additional information, 

such as important operating and maintenance instructions.

SAFE GROUNDING TERMINAL - Indicates primary safe ground

LOAD ON/OFF – Pressing the button turns on/off the output receptacles and the indicator light.

RJ45 RECEPTACLE – The receptacle provides network interface connections and telephone or telecommu

-

nications equipment should not be plugged into it.

Please do not discard the UPS or the UPS batteries as the UPS may have valve-regulated lead-acid batter

-

ies. Please recycle batteries appropriately.

 

The unit has a dangerous amount of voltage. If the UPS indicator is on, the unit’s outlets may have 

a dangerous amount of voltage even when not plugged into the wall outlet because the battery 

may continue to supply power.

Care should be taken to undertake installation indoors, free from electrically-conductive particles 

which are under temperature and humidity control, in order to reduce the risk of electric shock.

It is best to disconnect the device using the power supply cord. Ensure that the equipment is 

placed in a position near the outlet where easily accessible.

Except for replacing the batteries, all servicing on this equipment must be carried out by qualified 

service personnel.

Before conducting any maintenance, repair, or shipment, first ensure that everything is turned off 

completely and disconnected.

CAUTION

Содержание P90L-1500



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды