Xtreme Power Conversion TX90-1000 Скачать руководство пользователя страница 8

Страница: 8 / 26

Xtreme Power Conversion Corporation

TX90 User’s Manual

Page 8

Uninterruptible Power Supply

Step 5: Turn on the UPS

Press the ON/Mute button on the front panel for two seconds to power on the UPS.

Note: The battery charges fully during the first five hours of normal operation. Do not expect full battery run capa-

bility during this initial charge period.

Step 6: Install software

For optimal computer system protection, install UPS monitoring software to fully configure UPS shutdown. You

may insert provided CD into CD-ROM to install the monitoring software. If not, please follow steps below to down-

load and install monitoring software from the internet:

Go to the website

http://www.power-software-download.com

Click ViewPower software icon and then choose your required OS to download the software.

Follow the on-screen instructions to install the software.

4. When your computer restarts, the monitoring software will appear as an orange plug icon located in the

system tray, near the clock.

Step 7: External battery connection

Follow the below chart to make external battery connection.

To external battery

Step 8: External battery capacity configuration in software

To calculate accurate backup time of external batteries, it’s necessary to configure battery numbers in software.

The standard calculated capacity for one battery is 9Ah. If connecting to 100Ah batteries, then it’s equal to 11 in

parallel (100Ah / 9Ah ≈ 11 sets).

Содержание TX90-1000


























Результаты поиска

Содержание TX90-1000

Отзывы:

Бренды по названию

Популярные бренды

Xtreme Power Conversion TX90-1000, Руководство пользователя и инструкция по установке

Результаты поиска

Содержание TX90-1000

Отзывы:

Бренды по названию

Популярные бренды