manualshive.com logo in svg

XTM Racing 457 PRO, Руководство пользователя, Страница: 5 / 6

Поделиться
Скачать
XTM Racing 457 PRO Скачать руководство пользователя страница 5

TE001

(148310) Cylinder Head Screw Set (4) M3x16

TE2802G (148431) Cylinder Head

TE2803

(148432) Head Button

TE2804A (148433) Head Gasket - 0.10mm

TE2804B (148434) Head Gasket - 0.20mm

TE2831A (148435) Piston and Sleeve

TE2806

(148436) Wrist Pin

TE005

(148320) Wrist Pin Clips

TE008D

(148325) Connecting Rod

TE2809G (148437) Carburetor Assembly - Complete

TE015

(148402) Ball Bearing - Front (HG 7x19x6)

TE011

(148334) Collet for Flywheel

TE012A

(148336) Carburetor Retaining Bolt Assembly

TE2819H (148438) Crankcase

TE016A

(148404) Ball Bearing - Rear (HG 13x24x6)

TE020

(148346) Exhaust Gasket

TE2817B1 (148492) Crankshaft

TE9011

(148170) High Speed Needle Valve

TE9012

(148172) O-Ring for High Speed Needle Valve

TE9013

(148174) Needle Valve Seat

TE9015A (148439) Fuel Nipple

TE9010

(148374) Idle Stop Screw

TE9009

(148441) O-Ring for Idle Stop Screw

TE28901G (148442) Carburetor Body ONLY

TE010A

(148330) Upper O-Ring for Carburetor

TE010B

(148332) Lower O-Ring for Carburetor

TE9002

(148362) Carburetor Barrel

TE9003

(148364) O-Ring for Low Speed Needle Valve

TE9007

(148372) Low Speed Needle Valve

TE9004A (148443) Dust Boot

TE9018

(148378) Ball Cup

TE9005

(148370) Ball Link

TE9016

(148376) Set Screw for Ball Link

TS3A-1

(148444) Pull-Start Assembly

TS316

(148445) Pull-Start Handle

TROUBLESHOOTING GUIDE AND WARRANTY
INFORMATION CAN BE FOUND ON THE BACK

OF THIS SHEET

EXPLODED VIEW DRAWING AND PARTS

LIST FOR 457 PRO 6-PORT REAR EXHAUST EN-

GINE

Numbers that start with "T" are XTM Racing

manufacturer numbers.  The six-digit numbers are

provided for easy ordering convenience though

your local Global Hobbies dealer.

TS012C

(148199) Pull-Start String Tube - Molded

TS313

(148447) Pull-Start Cover

TS014

(148200) Pull-Start Bolts (3)

TS317

(148448) Pull-Start Recoil Spring

TS3030

(148495) Pull-Start String and Spool

TS002

(148214) Pull-Start Cushion Spring

TS1E

(148449) Backplate Assembly

TS005A

(148189) One-Way Bearing

TE12228 (148451)

O-Ring for Backplate

TS001C

(148446) Backplate

TS015

(148201) Backplate Screws (4) 3x6

TS004

(148210) Pull-Start Shaft

P/N 146032

Version 1 12/05

Содержание 457 PRO







Отзывы:

Нет отзывов