background image

Customer Service 1-888-707-1880   

                                                                                                     

Dyaco Canada Inc. 2019 

Email: [email protected] 

 

22 

Error Codes - DIAGNOSIS GUIDE 

Before contacting us for aid, please review the following information. It may save you both time and 
expense. This list includes common problems that may n

ot be covered under the treadmill’s warranty. 

 

Problem                      Meaning                                      Solution/Cause 

Console 
Showing LUBE 

Reminder to check 
lubrication under 
walking deck 

1. Check lubrication under walking belt. 
Reference belt deck lubrication procedure on page 20. 

Console 
Showing E1

 

Console shows E1 
8~10 seconds after 
pressing “Start” button. 

1. Does the motor run after “Start” button is pressed? 
2. Connector could be loose for the cable connecting between 
controller and speed sensor. 
3. Check the speed sensor for defects. 
4. Check the cable connecting the console and controller for 
proper connection. 

Console 
Showing E0 

Safety Switch 
Malfunction 

1. If safety key switch is placed properly? 
2. Is safety harness I the console connected properly? Any 
connector damaged? 
3. Is safety switch defective? 

Console 
Showing E2 

Over Current 
Protection 
Treadmill over loaded, 
controller protection 
is activated. 

1. Check for proper walking belt alignment. Make sure to 
lubricate belt periodically to minimize resistance. 
2. Is there any bearing damage? 
3. Has the motor overheated? 

Console 
Showing E4 

Improper Motor input 
voltage. 
Motor is not 
connected properly. 

1. Motor is not connected properly or not connected to the 
controller. 

Console 
Showing E5 

Communication 
disconnected between 
the console and 
the controller or 
communication error 

1. Check for proper connection between the console and 
controller. 

Console 
Showing E6 

Controller Malfunction 

1. Controller component failure 

Console 
Showing E7 

Abnormal Power Input 

1. Check for proper voltage input for treadmill. 

Console 
Showing Err 

Incline motor 
Malfunction 

1.  Incline motor disconnected or damaged 

 
 
 
ENGINEERING MODE

 

After removing the safety key, press 

PROGRAM

  and put on the safety key again to enterthe 

engineering mode. The sequence of the setting is the wheel size (42), unit of speed (metric 0, English 1), 
minimum speed (1.0KM/0.5MPH, maximum speed (16KM/10MPH), incline level (10).   
Press SPEED

/

to change the parameters. Press ENTER to set next parameter. After finishing setting 

parameters, press START to start calibrating and go to ready mode.

 

 

Содержание T3





































Отзывы: