Xstream X-HW2565AR Скачать руководство пользователя страница 31

Страница: 31 / 34

troubleshooting

SYMPTOM

PROBABLE CAUSE

REMEDY

Detergent will not

siphon into Low

Pressure Detergent

Mode

Detergent strainer is not

completely submerged in

detergent solution.

Check, submerge if necessary.

Detergent strainer

obstructed.

Inspect, clean or replace.

Detergent hose cut,

obstructed or kinked.

Inspect, clean or replace.

Detergent adjusting knob

turned to closed position.

Open adjusting knob. Refer to

“Cleaning with Detergents”.

Grip on adjustable nozzle is

not in low pressure mode.

Turn grip counterclockwise to

move to low pressure.

Nozzle assembly is plugged. Clean or replace.

Too many high pressure

hose extensions attached to

the water outlet.

Use one extension maximum.

Ball & Spring in Venturi

stuck.

Remove, clean or replace.

Water flows back into

detergent container.

Ball & Spring in Venturi

reversed, missing or

corroded.

Remove, clean or replace.

Water flows from the

nozzle when the trigger

gun is locked in the

“OFF” position

Trigger gun is

malfunctioning.

Repair or replace.

Water is leaking under

heat exchanger coil.

Safety Relief device is

relieving caused by an

unloader or pressure switch

problem.

1. Detect and correct unloader

or pressure switch problem.

2. Replace safety relief device.

NEVER run unit without safety

relief device. Doing so can cause

an explosion!

Burner will not ignite

Switch is not turned on.

Check switch position.

Out of fuel.

Refuel.

Trigger gun is closed.

Open trigger gun for pressure.

EMF Drive belt loose or

broken.

Adjust or replace as necessary.

Flexible coupler broken.

Replace.

Dirty or clogged fuel filter

Replace

Fuel pump sucking air.

Tighten all fuel intake

connections. Eliminate leaks in

intake line.

Fuel pump inoperative.

Check pressure, replace if

necessary.

Содержание X-HW2565AR



































Результаты поиска

Содержание X-HW2565AR

Отзывы:

Похожие инструкции для X-HW2565AR

Бренды по названию

Популярные бренды

Xstream X-HW2565AR, Руководство по эксплуатации

Результаты поиска

Содержание X-HW2565AR

Отзывы:

Похожие инструкции для X-HW2565AR

Бренды по названию

Популярные бренды