background image

3

 IMPORTANT NOTES – ELECTRICAL

•  Insulate any exposed electrical wiring (using heat shrink tubing or electrical tape) 

to prevent dangerous short circuits. Take maximum care in wiring, connecting 
and insulating cables. Make sure cables are always connected securely. Check 
connectors for if they become loose. And if so, reconnect them securely. Never use 
R/C models with damaged wires. A damaged wire is extremely dangerous, and can 
cause short-circuits resulting in fi re. Please have wires repaired at your local hobby 
shop.

•  Low battery power will result in loss of control. Loss of control can occur due to a 

weak battery in either the transmitter or the receiver. Weak running battery may also 
result in an out of control car if your car‘s receiver power is supplied by the running 
battery. Stop operation immediately if the car starts to slow down.

•  When not using RC model, always disconnect and remove battery. 
•  Do not disassemble battery or cut battery cables. If the running battery short-circuits, 

approximately 300W of electricity can be discharged, leading to fi re or burns. Never 
disassemble battery or cut battery cables.

•  Use a recommended charger for the receiver and transmitter batteries and follow 

the instructions correctly. Over-charging, incorrect charging, or using inferior 
chargers can cause the batteries to become dangerously hot. Recharge battery when 
necessary. Continual recharging may damage battery and, in the worst case, could 
build up heat leading to fi re. If battery becomes extremely hot during recharging, 
please ask your local hobby shop for check and/or repair and/or replacement.

•  Regularly check the charger for potential hazards such as damage to the cable, 

plug, casing or other defects. Ensure that any damage is rectifi ed before using 
the charger again. Modifying the charger may cause short-circuit or overcharging 
leading to a serious accident. Therefore do not modify the charger.

•  Always unplug charger when recharging is fi nished.
•  Do not recharge battery while battery is still warm. After use, battery retains heat. 

Wait until it cools down before charging. 

•  Do not allow any metal part to short circuit the receiver batteries or other electrical/

electronic device on the model.

•  Immediately stop running if your RC model gets wet as may cause short circuit. 
•  Please dispose of batteries responsibly. Never put batteries into fi re.

WARRANTY

XRAY guarantees this model kit to be free from defects in both material and 
workmanship within 30 days of purchase. The total monetary value under warranty 
will in no case exceed the cost of the original kit purchased. This warranty does not 
cover any components damaged by use or modifi cation or as a result of wear. Part 
or parts missing from this kit must be reported within 30 days of purchase. No part 
or parts will be sent under warranty without proof of purchase. Should you fi nd  a 
defective or missing part, contact the local distributor. Service and customer support 
will be provided through local hobby store where you have purchased the kit, 
therefore make sure to purchase any XRAY products at your local hobby store. This 
model racing car is considered to be a high-performance racing vehicle. As such 
this vehicle will be used in an extreme range of conditions and situations, all which 
may cause premature wear or failure of any component. XRAY has no control over 
usage of vehicles once they leave the dealer, therefore XRAY can only offer warranty 
against all manufacturer‘s defects in materials, workmanship, and assembly at point 
of sale and before use. No warranties are expressed or implied that cover damage 
caused by what is considered normal use, or cover or imply how long any model cars‘ 
components or electronic components will last before requiring replacement.

Due to the high performance level of this model car you will need to periodically 
maintain and replace consumable components. Any and all warranty coverage 
will not cover replacement of any part or component damaged by neglect, abuse, 
or improper or unreasonable use. This includes but is not limited to damage from 
crashing, chemical and/or water damage, excessive moisture, improper or no 

maintenance, or user modifi cations which compromise the integrity of components. 
Warranty will not cover components that are considered consumable on RC vehicles. 
XRAY does not pay nor refund shipping on any component sent to XRAY or its 
distributors for warranty. XRAY reserves the right to make the fi nal determination of 
the warranty status of any component or part.

Limitations of Liability

XRAY makes no other warranties expressed or implied. XRAY shall not be liable for any 
loss, injury or damages, whether direct, indirect, special, incidental, or consequential, 
arising from the use, misuse, or abuse of this product and/or any product or accessory 
required to operate this product. In no case shall XRAY‘s liability excess the monetary 
value of this product.

Take adequate safety precautions prior to operating this model. You are 
responsible for this model’s assembly and safe operation.

Disregard of the any of the above cautions may lead to accidents, personal 
injury, or property damage. XRAY MODEL RACING CARS assumes no 
responsibility for any injury, damage, or misuse of this product during 
assembly or operation, nor any addictions that may arise from the use 
of this product.
All rights reserved.

QUALITY CERTIFICATE

XRAY MODEL RACING CARS uses only the highest quality materials,  the best 
compounds for molded parts and the most sophisticated manufacturing processes of 
TQM (Total Quality Management). We guarantee that all parts of a newly-purchased 
kit are manufactured with the highest regard to quality. However, due to the many 
factors inherent in model racecar competition, we cannot guarantee any parts once 

you start racing the car. Products which have been worn out, abused, neglected or 
improperly operated will not be covered under warranty. 
We wish you enjoyment of this high-quality and high-performance RC car and wish 
you best success on the track!

In line with our policy of continuous product development, the exact specifications of the kit may vary. In the unlikely event of any 
problems with your new kit, you should contact the model shop where you purchased it, quoting the part number. We do reserve all 
rights to change any specification without prior notice. All rights reserved.

R/C & BUILDING TIPS

•  Make sure all fasteners are properly tightened. Check them periodically.
•  Make sure that chassis screws do not protrude from the chassis.
• For the best performance, it is very important that great care is taken to ensure the 

free movement of all parts.

•  Clean all ball-bearings so they move very easily and freely.
•  Tap or pre-thread the plastic parts when threading screws.
• Self-tapping screws cut threads into the parts when being tightened. Do not use 

excessive force when tightening the self-tapping screws because you may strip out 
the thread in the plastic. We recommended you stop tightening a screw when you 
feel some resistance.

•  Ask your local hobby shop for any advice.

Please support your local hobby shop. We at XRAY Model Racing Cars support all local 
hobby dealers. Therefore we ask you, if at all possible, to purchase XRAY products at 
your hobby dealer and give them your support like we do. If you have diffi culty fi nding 
XRAY products, please check out www.teamxray.com to get advice, or contact us via 
email at [email protected], or contact the XRAY distributor in your country.

  

IMPORTANT NOTES – NITRO FUEL

• Handle fuel only outdoors. Never handle nitro fuel indoors, or mix nitro fuel in a 

place where ventilation is bad.

•  Only use nitro fuel for R/C models. Do not use gasoline or kerosene in R/C models 

as it may cause a fi re or explosion, and ruin your engine.

• Nitro fuel is highly infl ammable, explosive, and poisonous. Never use fuel indoors 

or in places with open fi res and sources of heat. 

•  Always keep the fuel container cap tightly shut.
•  Always read the warning label on the fuel container for safety information. 
•  Nitro-powered model engines emit poisonous vapors and gasses. These vapors irritate 

eyes and can be highly dangerous to your health. We recommend wearing rubber or vinyl 
gloves to avoid direct contact with nitro fuel.

• Nitro fuel for RC model cars is made of the combination of the methyl alcohol, 

castor or synthetic oil, nitro methane etc. The fl ammability and volatility of these 
elements is very high, so be very careful during handling and storage of nitro fuel.

• Keep nitro fuel away from open fl ame, sources of heat, direct sunlight, high 

temperatures, or near batteries.

• Store fuel in a cool, dry, dark, well-ventilated place, away from heating devices, 

open fl ames, direct sunlight, or batteries. Keep nitro fuel away from children.

• Do not leave the fuel in the carburetor or fuel tank when the model is not in use. 

There is danger that the fuel may leak out.

•  Wipe up any spilled fuel with a cloth.
•  Be aware of spilled or leaking fuel. Fuel leaks can cause fi res or explosions.
• Do not dispose of fuel or empty fuel containers in a fi re. There is danger of 

explosion. 

Содержание XB808









































Отзывы: