Xray GTX8 2022 Скачать руководство пользователя

Страница: 38 / 52

SHOCK DAMPING

SHOCK PISTONS

960026

N M2.5

358040

S 2.5x6x0.5

#358163

GT SHOCK SHAFT 43MM (2)

There are two different thickness shims, use

them as shown. Use the same procedure

when building both front and rear shocks.

EXTREMELY IMPORTANT

Do not push the shock rod straight

through the lower shock body

assembly; O-ring damage may result.

Twist the shock rod through the

lower shock body assembly.

INCORRECT

CORRECT

6 holes

ø1.2mm pistons

NOTE ORIENTATION

971034

O 3.4x2

970100

O 10x1.5

BOOK

SET-UP

INCORRECT

DO NOT OVERTIGHTEN

The self-locking nut is overtightened, causing

distortion of the piston. This will negatively

affect the free movement of the piston in the

shock body.

DETAIL

CORRECT

TIGHTEN GENTLY

The self-locking nut is gently tightened. The

piston remains undistorted and fits inside the

shock body perfectly, ensuring smooth movement

of the piston.

DETAIL

Install the piston with Professional Multi

Tool (HUDY #183011).

11. SHOCK ABSORBERS

DETAIL

O-ring

Thin Shim

O-ring

Thick Shim

DO NOT USE

Содержание GTX8 2022





















































Результаты поиска

Содержание GTX8 2022

Отзывы:

Похожие инструкции для GTX8 2022

Бренды по названию

Популярные бренды

Xray GTX8 2022, Инструкция по эксплуатации

Результаты поиска

Содержание GTX8 2022

Отзывы:

Похожие инструкции для GTX8 2022

Бренды по названию

Популярные бренды