background image

2

BEFORE YOU START

The RX8 is a high-competition, high-quality, 1/8-scale on-road nitro car intended for persons aged 16 years and 

older with previous experience building and operating RC model racing cars. This is not a toy; it is a precision 

racing model. This model racing car is not intended for use by beginners, inexperienced customers, or by children 

without direct supervision of a responsible, knowledgeable adult. If you do not fulfill these requirements, please 

return the kit in unused and unassembled form back to the shop where you have purchased it.

Before building and operating your RX8, YOU MUST read through all of the operating instructions and instruction 

manual and fully understand them to get the maximum enjoyment and prevent unnecessary damage.

Read carefully and fully understand the instructions before beginning assembly.

Make sure you review this entire Instruction Manual and examine all details carefully. If for some reason you 

decide the RX8 is not what you wanted or expected, do not continue any further. Your hobby dealer cannot accept 

your RX8 kit for return or exchange after it has been partially or fully assembled.

Contents of the box may differ from pictures. In line with our policy of continuous product development, the exact 

specifications of the kit may vary without prior notice.

SAFETY PRECAUTIONS

WARNING:

 This product contains a chemical known to the state of California to cause cancer and birth 

defects or other reproductive harm.

CAUTION:

 CANCER HAZARD

Wash thoroughly after using. DO NOT use product while eating, drinking or using tobacco products. May 

cause chronic effects to gastrointestinal tract, CNS, kidneys, and blood. MAY CAUSE BIRTH DEFECTS.

When building, using and/or operating this model always wear protective glasses and gloves.

Take appropriate safety precautions prior to operating this model. You are responsible for this model‘s 

assembly and safe operation! Please read the instruction manual before building and operating this model 

and follow all safety precautions. Always keep the instruction manual at hand for quick reference, even after 

completing the assembly. Use only genuine and original authentic XRAY parts for maximum performance. 

Using any third party parts on this model will void guaranty immediately.

Improper  operation  may  cause  personal  and/or  property  damage.  XRAY  and  its    distributors  have  no 

control over damage resulting from shipping, improper construction, or improper usage. XRAY assumes and 

accepts no responsibility for personal and/or property damages resulting from the use of improper building 

materials,  equipment  and  operations.  By  purchasing  any  item  produced  by  XRAY,  the  buyer  expressly 

warrants  that  he/she  is  in  compliance  with  all  applicable  federal,  state  and  local  laws  and  regulation 

regarding the purchase, ownership and use of the item. The buyer expressly agrees to indemnify and hold 

harmless XRAY for all claims resulting directly or indirectly from the purchase, ownership or use of the 

product. By the act of assembling or operating this product, the user accepts all resulting liability. If the buyer 

is not prepared to accept this liability, then he/she should return this kit in new, unassembled, and unused 

condition to the place of purchase.

•  Keep the wheels of the model off the ground when checking the operation of the radio equipment.

•  Disconnect the battery pack before storing your model.

•  When learning to operate your model, go to an area that has no obstacles that can damage your model 

if your model suffers a collision.

•  Remove any sand, mud, dirt, grass or water before putting your model away.

•  If the model behaves strangely, immediately stop the model, check and clear the problem.

•  To prevent any serious personal injury and/or damage to property, be responsible when operating all 

remote controlled models.

•  The model car is not intended for use on public places and roads or areas where its operation can conflict with 

or disrupt pedestrian or vehicular traffic.

•  Because the model car is controlled by radio, it is subject to radio interference from many sources that 

are beyond your control. Since radio interference can cause momentary loss of control, always allow a 

safety margin in all directions around the model in order to prevent collisions.

•  Do not use your model:

  - Near real cars, animals, or people that are unaware that an RC car is being driven.

  - In places where children and people gather

  - In residential districts and parks

  - In limited indoor spaces

  - In wet conditions

  - In the street

  -  In areas where loud noises can disturb others, such as hospitals and residential areas.

  - At night or anytime your line of sight to the model may be obstructed or impaired in any way.

To prevent any serious personal injury and/or damage to property, please be responsible when operating 

all remote controlled models.

 

IMPORTANT NOTES – GENERAL

•  This product is not suitable for children under 16 years of age without the direct supervision of a 

responsible and knowledgeable adult.

•  Carefully read all manufacturers warnings and cautions for any parts used in the construction and use 

of your model.

•  Assemble this kit only in places away from the reach of very small children.

•  First-time builders and users should seek advice from people who have building experience in order to 

assemble the model correctly and to allow the model to reach its performance potential.

•  Exercise care when using tools and sharp instruments.

•  Take care when building, as some parts may have sharp edges.

•  Keep small parts out of reach of small children. Children must not be allowed to put any parts in their 

mouth, or pull vinyl bag over their head.

•  Read and follow instructions supplied with paints and/or cement, if used (not included in kit).

•  Immediately after using your model, do NOT touch equipment on the model such as the motor and 

speed controller, because they generate high temperatures. You may seriously burn yourself seriously 

touching them.

•  Follow the operating instructions for the radio equipment at all times.

•  Do not put fingers or any objects inside rotating and moving parts, as this may cause damage or 

serious injury as your finger, hair, clothes, etc. may get caught.

•  Be sure that your operating frequency is clear before turning on or running your model, and never 

share the same frequency with somebody else at the same time. Ensure that others are aware of the 

operating frequency you are using and when you are using it.

•  Use a transmitter designed for ground use with RC cars. Make sure that no one else is using the same 

frequency as yours in your operating area. Using the same frequency at the same time, whether it is 

driving, flying or sailing, can cause loss of control of the RC model, resulting in a serious accident. 

•  Always turn on your transmitter before you turn on the receiver in the car. Always turn off the receiver 

before turning your transmitter off.

FAILURE TO FOLLOW THESE INSTRUCTIONS WILL BE CONSIDERED AS ABUSE AND/OR NEGLECT.

CUSTOMER SUPPORT

 

XRAY Europe

K Výstavisku 6992

91101 Trenčín

Slovakia, EUROPE

Phone: +421-32-7401100

Fax: +421-32-7401109

Email: [email protected]

We have made every effort to make these instructions as easy to understand as possible. However, if you 

have any difficulties, problems, or questions, please do not hesitate to contact the XRAY support team at 

[email protected].  Also,  please  visit  our  Web  site  at  www.teamxray.com  to  find  the  latest  updates, 

set-up information, option parts, and many other goodies. We pride ourselves on taking excellent care of 

our customers.

You can join thousands of  XRAY fans and enthusiasts in our online community at:

  www.teamxray.com

XRAY RC America

2030 Century Center Blvd #15, Suite 109

75062 Irving

Texas, USA

Phone: (214) 744-2400

Fax: (214) 744-2401

Email: [email protected]

   

IMPORTANT NOTES – NITRO ENGINES

• Always test the brakes and the throttle before starting your engine to avoid losing control of the model.

• Make sure the air filter is clean and oiled. 

• Never run your engine without an air filter. Your engine can be seriously damaged if dirt and debris get 

inside the engine.

• For proper engine break-in, please refer to the manual that came with the engine.

• Do not run near open flames or smoke while running your model or while handling fuel.

• Some parts will be hot after operation. Do not touch the exhaust or the engine until they have cooled. 

These parts may reach 275°F during operation!

Содержание 2016 RX8

















































Отзывы: