xpr B100PROX-MF Скачать руководство пользователя страница 4

Страница: 4 / 20

www.xprgroup.com

3. MOUNTING

WIRING

If the biometric reader is installed and used outdoor, the reader MUST be fitted with MCD-MINI cover available in our

accessories in order to protect the sensor from direct rainfall. The operating temperature of the product is between -15ºC - +

50ºC. If the reader is installed in an environment where the temperature can drop below -10ºC or/and if the sensor could only

be exposed to direct sunlight, it is strongly recommended to install the reader inside a third party sealed wall mount box

(fitted with additional heater if very low temperature) to keep a constant sensor level performance. XPR™ cannot guarantee

the functionality of the product if measures and advice before are not followed.

It is also strongly recommended to use double technology biometric readers when use outdoor to offer first higher security

but also the possibility to use different readers depending on users.

4 (3 x 30mm)

1 (M3 x 6mm)

Note:

The conversion from 7byte ID to 4 byte ID is only possible with cards that have 7 byte ID Number. Those are: Mifare plus, Desfire and Ultralight.

The number is converted according to NXP algorithm. It corresponds to the number obtained by the USB desktop reader.

Содержание B100PROX-MF




















