XOS Petra MAX Скачать руководство пользователя страница 22

XOS  

|

  801377-02  

|

  Rev D  

|

  English

 

Page 

21

 of 

22 

Troubleshooting 

Warning Message 

Condition 

Possible Cause(s) 

Solutions 

MESSAGE [TOTAL 1] 

MCODE 10016: WARNING – 

Empty Cup. 

Poor data quality 

Not enough sample in the 

cup. 

Remake the sample and measure. 

MESSAGE [TOTAL 1] 

MCODE 10015: WARNING – 

Result out of calibration range (S) 

Element result is not 

within the calibration 

range. 

Used wrong cal curve for 

measurement or wrong 

sample. 

Remake sample and validate the cal curve 

being used for measurement.  Re-measure 

sample. 

Tube is hot (60°C)!  Analyzer will 

not measure at 65°C. 

X-ray tube is close

to 65°C.  At this

temperature, the

analyzer will not

measure.

Continuous use 

Stop measuring until the message 

disappears, which occurs when the x-ray 

tube has cooled below 60°C.  
The message pop-up will NOT clear by 

pressing OK while the tube temperature is 

close to 65°C. The message auto-clear 

when the tube cools. 

Error Message 

Condition 

Possible Cause(s) 

Solutions 

Measurement inconclusive. 

Please contact XOS technical 

support.  

Poor data quality 

Usually happens when 

the spectrum is unusual, 

or not enough sample in 

cup.  

Make a new sample and re-measure to see 

if the error disappears; if not, try to measure 

a validation sample  

ERROR - Internal Error 

Please be certain the door is 

closed and press OK to try again. 

Sample lid must be 

properly closed for 

analyzer to work 

correctly 

Sample lid was not closed 

at start-up (after power-

on).  

Open and close the sample lid. Restart 

Petra by pressing the Power button. If this 

error recurs, contact XOS Technical 

Support.  

Содержание Petra MAX


























Отзывы: