background image

Input signal separately to TV/SCART/AV/S terminal, connect AUDIO/VIDEO OUT 

terminal to monitor, check the output sound of AUDIO OUT is normal, and output 
picture of VIDEO OUT is normal. (LC-20H3 S/20H4 S)   

 

3.4  SCART connector 
3.4.1 Inspection of connector content of SCART OUTPUT   

Input signal to different TV/SCART/AV/S/VGA terminals, connect SCART 

connector to TV as monitor. Select SCART OUTPUT item of menu to TV, check output 
of picture and sound if they are all TV picture and sound, and if they are normal; select 
SCART OUTPUT item of menu to MINITOR, check picture and  sound if they are 
current picture and sound of signal (Under VGA state, switch to formal VGA) and 
check if they are normal.       
 

(* Note: For the TV sets produced in the initial stage the picture is colorless for the signal 

output from AV OUTPUT,SCART OUTPUT under S-terminal)   

3.4.2 inspection of special function of SCART INPUT 
a) After power supply on, input SCART to signal generator, the set should 
automatically switch to AV1or AV1 RGB state. 
b) SCART signal generator outputs CVBS signal (color bar + multi-wave group ), 
observe if the picture of the set is normal. The normal screen should be AV1: change 
SCART signal to RGB format, the normal screen should be AV1 RGB. 
c) Disconnect SCART signal, the set could come back to current TV state. 
   

  (Note: This special function is not applicable to VGA) 

3.5  VGA connector 

Input VGA signal (K7253 signal generator), input different VGA format signal listed 

in table 2, after completion of the auto calibration, check the picture and sound if they 
are normal. If there is interfere in picture, push the auto-adjustment key on the remote 
control set one more time, check if the display is normal.   
3.6 Factory preset 
    Enter factory menu, perform factory presetting under TV state. 
3.7 Packing for factory outgoing   

Check accessory, then pack. 

Table 2.VGA format signal 

screen size 

resolution 

Image clock 

(MHz) 

H-SYNC 

(kHz) 

V-SYNC 

(Hz) 

remark 

640x480 @ 60 

25.175 

31.469 

59.900 

 

720x400 @ 70 

28.322 

31.469 

70.086 

 

800x600 @ 60 

40.000 

37.879 

60.317 

 

1024x768 @ 60 

65.000 

48.363 

60.004 

 

640x480 @ 75 

31.500 

37.500 

75.000 

 

800x600 @ 75 

49.500 

46.875 

75.000 

 

15” 

1024x768 @ 75 

78.750 

60.023 

75.029 

 

640x480 @ 60 

25.175 

31.469 

59.900 

 

720x400 @ 70 

28.322 

31.469 

70.086 

 

800x600 @ 60 

40.000 

37.879 

60.317 

 

17” 

1024x768 @ 60 

65.000 

48.363 

60.004 

 

Содержание LC17H3S
































Отзывы: