Xkitz XAMP-M2, Руководство по сборке и эксплуатации, Страница: 3 / 12

6/17/2017 XKITZ XAMP-M2
3
Circuit Board Assembly
You're ready to begin assembling your XAMP-M2 circuit board. Assemble the board in the order listed in Table
1. The components for the standard kit (in bags marked ‘Bag A’ and ‘Bag B’) support the default configuration:
UNBALANCED signal mode. If you purchased the BALANCED signal mode upgrade, you will have an additional
bag labeled ‘Balanced Mode Upgrade’, which contains the components required to configure the XAMP-M2 to
support balanced input. Table 1 below lists the parts and assembly steps for the standard board. Table 2 has
the parts lists and specific instructions for the Balanced mode option. Use the install check boxes on the right
side to track your progress. The 'Install Notes' column will alert you to any special instructions (listed below) for
each of the components. We recommend reading and understanding all the design notes before you start your
assembly. The PCB has large, heavy metal planes, which makes de-soldering components extremely difficult.
Soldering a component in the wrong location may be a difficult mistake to recover from.
Table 1. Circuit Board Parts List – Parts Used for All Configuration Options
Pack
√
Device Value Marking Qty
Reference
Designators
Bag Install
Notes
Install
√
CIRCUIT BOARD (PCB) REV 5.1 XAMP-M2 1
RESISTOR 1K,1% BRN-BLK-BLK-BRN-BRN 10
R1,R14,R15,
R16,R19,R25,
R27,R45,R50,
R62 A
RESISTOR 10K,1% BRN-BLK-BLK-RED-BRN 6
R4,R7,R10,
R12,R49,R51 A
1
RESISTOR 20K,1% RED-BLK-BLK-RED-BRN 3 R2,R11,R17 A 1
RESISTOR 10K,1% BRN-BLK-BLK-RED-BRN 3 R21,R22,R23 A 2
RESISTOR 20K,1% RED-BLK-BLK-RED-BRN 2 R20 ,R24 A 2
RESISTOR 4.7,1% YEL-VIO-BLK-SLV-BRN 2 R3,R18 A
RESISTOR 10 BRN-BLK-BLK 1 R26 A
RESISTOR 15K,1% BRN-GRN-BLK-RED-BRN 1 R28 A
RESISTOR 82.5K,1% GRY-RED-GRN-ORA-BRN 1 R6 A
RESISTOR 100K,1% BRN-BLK-BLK-ORA-BRN 1 R9 A
RESISTOR 200K,1% RED-BLK-BLK-ORA-BRN 2 R5,R8 A
DIODE 1N5240 1N5240 1 D1 A 3
CAPACITOR 10pF 100 2 C11,C14 A 4
CAPACITOR 100pF 101 1 C59 A 4
CAPACITOR .1uF 104 9
C2,C7,C9,
C10,C26,C27,
C28,C29,C32 A
4
CAPACITOR .47uF 474 2 C30,C31 A 4
CAPACITOR 10uF 106 4
C12,C13,C18,
C21 A
4
CAPACITOR .015uF, 5% 153 (Blue colored ones) 10
C49,C50,C51,
C52,C53,C54,
C55,C56,C57,
C58 A
4
CAPACITOR
BSC Configuration Cap:
One of: (See Table 3)
.022uF 223
.033uF 333
.047uF 473
1 C42
A
5
SOCKET – 8 PIN 1 U2 A 6
SOCKET – 14 PIN 2 U1,U3 A 6
OP AMP IC TL072 TL072 (or OPA2227) 1 U2 A 7
OP AMP IC TL074 TL074 (or OPA4227) 2 U1,U3 A 7
SOCKET – 20 PIN 1 XO MODULE A 8
COMPONENT CARRIER – 20
PIN
1 XO MODULE 8
SPADE TERMINAL 6
SP1,SP2,SP3,
SP4,SP5, SP6 A
TRANSISTOR 2N3904 2N3904 2 Q1,Q3 A 9
VOLTAGE REGULATOR LM317TG LM317TG 1 U4 9
TRIMPOT 10K R10K 3
VR1,
VR2,VR3 A
10
ELECTROLYTIC CAPACITOR 10uF 10uF 1 C5 A 11
ELECTROLYTIC CAPACITOR 22uF 22uF 3 C1,C6,C8 A 11
ELECTROLYTIC CAPACITOR 100uF 100uF 2 C25,C39 A 11
ELECTROLYTIC CAPACITOR 1000uF 1000uF 1 C3 B 11
ELECTROLYTIC CAPACITOR 3300uF 3300uF 2 C4,C24 B 11