manualshive.com logo in svg

Xkitz XAMP-M2, Руководство по сборке и эксплуатации, Страница: 1 / 12

Поделиться
Скачать
Xkitz XAMP-M2 Скачать руководство пользователя страница 1

6/17/2017 

XKITZ   XAMP-M2 

1 

Audio Bi-Amplifier, 40W, Mono, 2-Way Active Crossover 

Model XAMP-M2  

Assembly and Operator’s Manual 

Rev 5.1.2 

Xkitz.com 

 

Features

 

•

 

2-way active cross-over drives dual amplifiers for driving separate woofer and  tweeter 

•

 

Linkwitz-Riley crossover, 4

th

 order, 24dB/Octave roll-off 

•

 

Uses the highly respected LM4766 Chip Amp to produce 40W peak on both woofer and tweeter 

•

 

Crossover frequency configuration components are on a single socketed module - quick and easy to change 
the XO frequency by simply snapping in a new module.  

•

 

Wide range of standard XO frequency modules are offered by Xkitz, any frequency available on request 

•

 

Baffle Step Compensation, optional, adjustable and configurable to support various baffle sizes 

•

 

Supports unbalanced signal inputs by default, balanced audio signaling is available as an add-on option. 

 

Unbalanced signals are connected via standard RCA jacks 

 

Balanced signals are connected via optional 3.5mm TRS jack. The TRS jack is wired to be directly 
compatible with the new hi-def audio players such as the Pono 

•

 

Specifications: 

 

THD:  

 

 

0.044% 

 

THD+N: 

  

 

0.046% 

 

Frequency Response   

Linear from 20Hz – 80KHz 

 

CMRR (balanced input): 

> 55dB 

 

Input Impedance 

 

20K ohms unbalanced, 40K balanced 

 

Input Overload: 

 

3.8V peak-to-peak 

 

Voltage Gain: 

 

Adjustable, Max 26dB

 

 

Power Output Per Channel:    12W RMS into 8 Ohms, 21W RMS into 4 Ohms 

 

Filter Topology: 

 

Linkwitz-Riley, Constant Voltage, 4

th

 Order, 24dB/octave 

 

Amplifier Type: 

 

Class AB 

 

Power supply:  

 

Single positive DC rail (no negative supply required) 22V–50V DC 

•

 

Applications: 

•

 

Active Monitors 

•

 

Speaker Bi-Amp conversions 

•

 

Bi-Amp’ed Active Speaker System 

•

 

Portable boom-box 

•

 

Portable guitar amplifier 

•

 

Custom speaker systems 

•

 

Channels are phase aligned to within a fraction of a degree to minimize distortion around the XO frequency 

•

 

Separate bass and treble output level adjustments via on-board multi-turn trim-pots 

•

 

Low power consumption and no negative supply needed - perfect for portable battery powered speakers 

•

 

Quiet power ON / power OFF  

•

 

This is a mono device, two units are needed for stereo operation 

•

 

PCB Dimensions: 3.4” x 3” x 2” high (86mm x 76mm x 51mm) 

•

 

This  is  an  intermediate  electronic  kit  containing  85  components,  and  can  be  assembled  in  about  1-2  hours

Содержание XAMP-M2













Отзывы:

Нет отзывов