Xilinx Zynq-7000 Скачать руководство пользователя страница 190 | Manualshive

Страница: 190 / 678

background image

Zynq-7000 AP SoC and 7 Series FPGAs MIS v4.1

190

UG586 November 30, 2016

Chapter 1:

DDR3 and DDR2 SDRAM Memory Interface Solution

ADDR_MAP

Bank and byte lane

position information for

the address. 12-bit

parameter provided per

pin.
• [11:8] – Bank position.

Values of 0, 1, or 2 are

supported

• [7:4] – Byte lane position

within a bank. Values of

0, 1, 2, or 3 are

supported.

• [3:0] – Bit position

within a byte lane.

Values of [0, 1, 2, . . ., A,

B] are supported.

This parameter varies

based on the pinout and

should

not

be changed

manually in generated

design.

Upper-most Data or Address/Control byte group selected bank

is referred to as Bank 0 in parameters notation. Numbering of

banks is 0, 1, and 2 from top to bottom.
Byte groups T0, T1, T2, and T3 are numbered in parameters as

3, 2, 1 and 0, respectively.
Bottom-most pin in a byte group is referred as “0” in MAP

parameters. Numbering is counted from 0 to 9 from

bottom-most pin to top pin with in a byte group by excluding

DQS

I/Os.

DQS_N

and

DQS_P

pins of the byte group are

numbered as A and B, respectively.
192'h000_000_039_038_037_036_035_034_033_032_031_029_0

28_027_026_02B: This parameter is denoted for Address width

of 16 with 12 bits for each pin. In this case the Address width is

14 bits. Ordering of parameters is from MSB to LSB (that is,

ADDR[0] corresponds to the 12 LSBs of the parameter.
12'h02B: Address pin placed in bank 0, byte lane 1, at location B.
12'h235: Address pin placed in bank 2, byte lane 0, at location 5.

BANK_MAP

Bank and byte lane

position information for

the bank address. See the

description.

This parameter varies

based on the pinout and

should

not

be changed

manually in generated

design.

See the

example.

CAS_MAP

Bank and byte lane

position information for

the CAS command. See the

description.

This parameter varies

based on the pinout and

should

not

be changed

manually in generated

design.

See the

example.

CKE_MAP

Bank and byte lane

position information for

the CKE. This parameter

is referred to as one of

the Address/Control byte

groups. See

description. This

parameter varies based

on the pinout and should

not be changed manually

in generated design.

See the

example.

Table 1-66:

DDR2/DDR3 SDRAM Memory Interface Solution Pinout Parameters

(Cont’d)

Parameter

Description

Example

«
...
188
189
190
191
192
...
»

Содержание Zynq-7000







































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Zynq-7000

Бренд: Vutec Страницы: 11

Бренд: Kenwood Страницы: 38

Бренд: Kenwood Страницы: 36

Essential MC-400S

Бренд: Wilfa Страницы: 54

Бренд: NEC Страницы: 12

Mosaic Connect Box

Бренд: NEC Страницы: 18

Бренд: NEC Страницы: 8

Бренд: NEC Страницы: 2

Бренд: NEC Страницы: 6

Бренд: NEC Страницы: 20

Бренд: NEC Страницы: 14

Бренд: NEC Страницы: 70

Бренд: NEC Страницы: 28

Бренд: NEC Страницы: 261

Бренд: NEC Страницы: 1

Multiquick Minipimer MR 40

Бренд: Braun Страницы: 35

Бренд: Ankarsrum Страницы: 34

Бренд: Navitar Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды