Xilinx Vivado MIPI CSI-2 страница 78 Скачать руководство пользователя

Страница: 78 / 90

MIPI CSI-2 RX Subsystem v4.0

PG232 July 02, 2019

www.xilinx.com

Appendix A

Verification, Compliance, and
Interoperability

The MIPI CSI-2 RX Subsystem has been verified using both simulation and hardware testing.

A highly parameterizable transaction-based simulation test suite has been used to verify

the subsystem. The tests include:

• Different lane combinations and line rates
• High-Speed Data reception with short/long packets, different virtual channels and

different data types.

• All possible interleaving cases (data type and virtual channel)
• All possible output pixel, data type combinations.
• Recovery from error conditions
• Register read and write access

Hardware Validation

The MIPI CSI-2 RX Subsystem is tested in hardware for functionality, performance, and

reliability using Xilinx® evaluation platforms. The MIPI CSI-2 RX Subsystem verification test

suites for all possible modules are continuously being updated to increase test coverage

across the range of possible parameters for each individual module.

A series of MIPI CSI-2 RX Subsystem test scenarios are validated using the Xilinx

development boards listed in

Table A-1

. These boards permit the prototyping of system

designs where the MIPI CSI-2 RX Subsystem processes different short/long packets received

on serial lines.

Xilinx 7 series FPGA devices do not have a native MIPI IOB support. You will have to target

either the HR bank I/O or the HP bank I/O for the MIPI IP implementation. For more

Table A-1:

Xilinx Development Board

Target Family

Evaluation Board

Characterization Board

Zynq® Ult™ MPSoC

ZCU102

N/A

Zynq 7000

ZC702

N/A

Send Feedback

Содержание Vivado MIPI CSI-2



























































































Результаты поиска

Содержание Vivado MIPI CSI-2

Отзывы:

Похожие инструкции для Vivado MIPI CSI-2

Бренды по названию

Популярные бренды

Xilinx Vivado MIPI CSI-2, Руководство по эксплуатации продукта

Результаты поиска

Содержание Vivado MIPI CSI-2

Отзывы:

Похожие инструкции для Vivado MIPI CSI-2

Бренды по названию

Популярные бренды