Xilinx Virtex UltraScale+ FPGAs Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 145

Xilinx Virtex UltraScale+ FPGAs Скачать руководство пользователя страница 59

Using TXPROGDIVCLK to Drive the TX Interface

Depending on the TXUSRCLK and TXUSRCLK2 frequencies, there are different ways UltraScale
architecture clock resources can be used to drive the parallel clock for the TX interface.

show different ways clock resources can be used to drive the parallel clocks

for the TX interface.

Depending on the input reference clock frequency and the required line rate, a BUFG_GT with a
properly configured divide setting is required. The Ult FPGAs GTM Transceivers Wizard
creates a sample design based on different design requirements for most cases.

TXPROGDIVCLK Driving GTM Transceiver TX in 64-Bit, 80-Bit, or 128-

Bit Mode

In the following figure, TXPROGDIVCLK is used to drive TXUSRCLK and TXUSRCLK2 in 64-bit,
80-bit, or 128-bit mode in a single-lane configuration. In all cases, the frequency of TXUSRCLK2
is equal to TXUSRCLK.

Figure 26:

Single Lane—TXPROGDIVCLK Drives TXUSRCLK and TXUSRCLK2 (64-Bit, 80-

Bit, or 128-Bit Mode)

Design in UltraScale

Architecture

UltraScale

Devices GTM

Transceiver

TXPROGDIVCLK

BUFG_GT

1

TXUSRCLK2

2

TXUSRCLK

2,3

TXDATA (TX data width = 64/80/128 bits)

X20911-111918

Notes relevant to the figure:

1. For details about placement constraints and restrictions on clocking resources (such as

BUFG_GT and BUFG_GT_SYNC), refer to the UltraScale Architecture Clocking Resources User

Guide (

2. F

TXUSRCLK2

= F

TXUSRCLK

.

3. TXUSRCLK can be tied to

1’b0

if GEN_TXUSRCLK =

1’b1

.

Chapter 3: Transmitter

UG581 (v1.0) January 4, 2019

Virtex Ult GTM Transceivers

59

«
...
57
58
59
60
61
...
»

Содержание Virtex UltraScale+ FPGAs


















































































































































Отзывы:

Нет отзывов