Xilinx Virtex-II Pro PPC405 Скачать руководство пользователя страница 194 | Manualshive

Страница: 194 / 562

Xilinx Virtex-II Pro PPC405 Скачать руководство пользователя страница 194

502

www.xilinx.com

March 2002 Release

1-800-255-7778

Virtex-II Pro™ Platform FPGA Documentation

Chapter 7:

Exceptions and Interrupts

R

check exception when machine-check interrupts are disabled. It is recommended that
instruction machine-check interrupt handlers clear the ESR[MSI] bit prior to returning to
the interrupted program.

If machine-check interrupts are enabled (MSR[ME]

=

1), an instruction machine-check

exception sets ESR[MCI] and clears all other ESR bits.

The ESR is a privileged SPR with an address of 980 (0x3D4) and is read and written using
the

mfspr

and

mtspr

instructions.

Data Exception-Address Register

The data exception-address register (DEAR) is a 32-bit register that contains the memory-
operand effective address of the data-access instruction that caused one of the following
exceptions:

•

Alignment exception.

•

Data-storage exception.

•

Data TLB-miss exception.

shows the format of the DEAR register.

The DEAR is a privileged SPR with an address of 981 (0x3D5) and is read and written using
the

mfspr

and

mtspr

instructions.

Interrupt Reference

This section describes each interrupt, using the following outline:

•

The name of each interrupt is shown, followed by its exception-vector offset.

•

Interrupts are classified based on whether they are critical or noncritical, synchronous
or asynchronous, and precise or imprecise.

•

The conditions that cause the exception for which the interrupt occurs are described.

•

The methods used to enable and disable (mask) the interrupt are described, if
applicable.

•

The values of the registers affected by taking the interrupt are shown.

0

31

Data-Access Effective Address

Figure 7-6:

Data Exception-Address Register (DEAR)

«
...
192
193
194
195
196
...
»

Содержание Virtex-II Pro PPC405



















































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды