manualshive.com logo in svg

Xilinx Virtex-5 FPGA ML561, Руководство пользователя

Xilinx Virtex-5 FPGA ML561 - мощный продукт, предлагающий широкие возможности для пользователей. Для удобства пользования, предоставляется User Manual, который можно скачать бесплатно с manualshive.com. Пользователи могут найти подробные инструкции и руководства по использованию продукта для оптимальной производительности.

Поделиться
Скачать
background image

56

www.xilinx.com

Virtex-5 FPGA User Guide

UG190 (v5.0) June 19, 2009

Chapter 2:

Clock Management Technology

DCM Status and Data Output Ports

Locked Output - LOCKED

The LOCKED output indicates whether the DCM clock outputs are valid, i.e., the outputs 
exhibit the proper frequency and phase. After a reset, the DCM samples several thousand 
clock cycles to achieve lock. After the DCM achieves lock, the LOCKED signal is asserted 
High. The DCM timing parameters section of the 

Virtex-5 FPGA Data Sheet

 provides 

estimates for locking times.

To guarantee an established system clock at the end of the start-up cycle, the DCM can 
delay the completion of the device configuration process until after the DCM is locked. The 
STARTUP_WAIT attribute activates this feature. The 

STARTUP_WAIT Attribute

 

description provides further information.

Until the LOCKED signal is asserted High, the DCM output clocks are not valid and can 
exhibit glitches, spikes, or other spurious movement. In particular, the CLK2X output 
appears as a 1x clock with a 25/75 duty cycle.

Phase-Shift Done Output - PSDONE

The phase-shift done (PSDONE) output signal is synchronous to PSCLK. At the 
completion of the requested phase shift, PSDONE pulses High for one period of PSCLK. 
This signal also indicates a new change to the phase shift can be initiated. The PSDONE 
output signal is not valid if the phase-shift feature is not being used or is in fixed mode.

Status or Dynamic Reconfiguration Data Output - DO[15:0]

The DO output bus provides DCM status or data output when using dynamic 
reconfiguration (

Table 2-4

). Further information on using DO as the data output is 

available in the Dynamic Reconfiguration chapter of the 

Virtex-5 FPGA Configuration Guide

 

for more information.

If the dynamic reconfiguration port is not used, using DCM_BASE instead of DCM_ADV 
is strongly recommended.

Table 2-4:

DCM Status Mapping to DO Bus

DO Bit

Status

Description

DO[0]

Phase-shift overflow

Asserted when the DCM is phase-shifted beyond the 
allowed phase-shift value or when the absolute delay 
range of the phase-shift delay line is exceeded. DO[0] is 
deasserted if the phase shift feature is not used 
(CLKOUT_PHASE_SHIFT=NONE).

DO[1]

CLKIN stopped

Asserted when the input clock is stopped (CLKIN 
remains High or Low for one or more clock cycles). 
When CLKIN is stopped, the DO[1] CLKIN stopped 
status is asserted within nine CLKIN cycles. When 
CLKIN is restarted, CLK0 starts toggling and DO[1] is 
deasserted within nine clock cycles.

DO[2]

CLKFX stopped

Asserted when CLKFX stops. The DO[2] CLKFX 
stopped status is asserted within 260 cycles after 
CLKFX stopped. CLKFX does not resume, and DO[2] is 
not deasserted until the DCM is reset. DO[2] is 
deasserted if the CLKFX/CLKFX180 output is not used.

Содержание Virtex-5 FPGA ML561


































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Virtex-5 FPGA ML561

Patton electronics 2888 Getting Started Manual preview
2888
Бренд: Patton electronics Страницы: 51
Jabra A330 Multiuse User Manual preview
A330 Multiuse
Бренд: Jabra Страницы: 15
DAQ system PCIe-FRM13 User Manual preview
PCIe-FRM13
Бренд: DAQ system Страницы: 41
DAQ system PCIe-SER01 User Manual preview
PCIe-SER01
Бренд: DAQ system Страницы: 19
NXP Semiconductors TWR-SB0410-36EVB User Manual preview
TWR-SB0410-36EVB
Бренд: NXP Semiconductors Страницы: 26
Ruckus Wireless SmartZone 3.6 Command Reference Manual preview
SmartZone 3.6
Бренд: Ruckus Wireless Страницы: 102
Internet Security Systems Proventia A1204 User Manual preview
Proventia A1204
Бренд: Internet Security Systems Страницы: 42
Buffalo LinkStation Quick Setup Manual preview
LinkStation
Бренд: Buffalo Страницы: 2
Giacomini KPM36Y002 Manual preview
KPM36Y002
Бренд: Giacomini Страницы: 2
axing EOC 30-01 Quick Start Manual preview
EOC 30-01
Бренд: axing Страницы: 4
Xyclop XC-16CH-NVR-4TB Quick Start Manual preview
XC-16CH-NVR-4TB
Бренд: Xyclop Страницы: 19
Patton electronics 593/45 User Manual preview
593/45
Бренд: Patton electronics Страницы: 8
LevelOne WBA-4000 User Manual preview
WBA-4000
Бренд: LevelOne Страницы: 49
Z-Wave IOMOD10F Hardware User Manual preview
IOMOD10F
Бренд: Z-Wave Страницы: 42
M-system M5XSBS Instruction Manual preview
M5XSBS
Бренд: M-system Страницы: 4
Vivotek ND8212W Hardware Installation Manual preview
ND8212W
Бренд: Vivotek Страницы: 46
ACTi GNR-410 Quick Installation Manual preview
GNR-410
Бренд: ACTi Страницы: 12
Primera DUP-11 User Manual preview
DUP-11
Бренд: Primera Страницы: 82

Бренды по названию

Популярные бренды

Загрузить еще бренды