manualshive.com logo in svg

Xilinx Virtex-5 FPGA ML561, Руководство пользователя, Страница: 359 / 385

Поделиться
Скачать
Xilinx Virtex-5 FPGA ML561 Скачать руководство пользователя страница 359

Virtex-5 FPGA User Guide

www.xilinx.com

359

UG190 (v5.0) June 19, 2009

Input Serial-to-Parallel Logic Resources (ISERDES)

DATA_WIDTH Attribute

The DATA_WIDTH attribute defines the parallel data output width of the serial-to-parallel 
converter. The possible values for this attribute depend on the INTERFACE_TYPE and 
DATA_RATE attributes. See 

Table 8-3

 for recommended data widths.

When the DATA_WIDTH is set to widths larger than six, a pair of ISERDES_NODELAY 
must be configured into a master-slave configuration. See 

“ISERDES Width Expansion.”

 

Width expansion is not allowed in memory mode.

INTERFACE_TYPE Attribute

The INTERFACE_TYPE attribute determines whether the ISERDES_NODELAY is 
configured in memory or networking mode. The allowed values for this attribute are 
MEMORY or NETWORKING. The default mode is MEMORY.

When INTERFACE_TYPE is set to NETWORKING, the Bitslip submodule is available and 
the OCLK port is unused. BITSLIP_ENABLE must be set to TRUE, and the Bitslip port tied 
Low to disable Bitslip operation when the Bitslip module is not used in networking mode. 
When set to MEMORY, the Bitslip submodule is not available (BITSLIP_ENABLE must be 
set to FALSE), and the OCLK port can be used.

Figure 8-5

 illustrates the ISERDES_NODELAY internal connections when in Memory 

mode.

Table 8-3:

Recommended Data Widths

INTERFACE_TYPE

DATA_RATE

Recommended Data Widths

NETWORKING

SDR

2, 3, 4, 5, 6, 7, 8

DDR

4, 6, 8, 10

MEMORY

SDR

None

DDR

4

Содержание Virtex-5 FPGA ML561


































































































































































































































































































































































































Отзывы:

Нет отзывов