manualshive.com logo in svg

Xilinx Virtex-5 FPGA ML561, Руководство пользователя, Страница: 120 / 385

Поделиться
Скачать
Xilinx Virtex-5 FPGA ML561 Скачать руководство пользователя страница 120

120

www.xilinx.com

Virtex-5 FPGA User Guide

UG190 (v5.0) June 19, 2009

Chapter 4:

Block RAM

Additional Block RAM Features in Virtex-5 Devices

Optional Output Registers 

The optional output registers improve design performance by eliminating routing delay to 
the CLB flip-flops for pipelined operation. An independent clock and clock enable input is 
provided for these output registers. As a result the output data registers hold the value 
independent of the input register operation. 

Figure 4-5

 shows the optional output register.

Independent Read and Write Port Width Selection

Each block RAM port has control over data width and address depth (aspect ratio). The 
true dual-port block RAM in Virtex-5 FPGAs extends this flexibility to Read and Write 
where each individual port can be configured with different data bit widths. For example, 
port A can have a 36-bit Read width and a 9-bit Write width, and port B can have a 18-bit 
Read width and a 36-bit Write width. See 

“Block RAM Attributes,” page 128

.

If the Read port width differs from the Write port width, and is configured in 
WRITE_FIRST mode, then DO shows valid new data for all the enabled write bytes. The 
DO port outputs the original data stored in memory for all not enabled bytes.

Independent Read and Write port width selection increases the efficiency of implementing 
a content addressable memory (CAM) in block RAM. This option is available for all 
Virtex-5 FPGA true dual-port RAM port sizes and modes. 

X-Ref Target - Figure 4-5

Figure 4-5:

Block RAM Logic Diagram (One Port Shown)

Register

Optional

Inverter

Latches

Register

Address

DI

WE

EN

CLK

Write

Strobe

Read
Strobe

Q

D

Q

D

DO

Control Engine

Configurable Options

UG190_4_06_040606

Memory

Array

(common to

both ports)

Latch
Enable

Содержание Virtex-5 FPGA ML561


































































































































































































































































































































































































Отзывы:

Нет отзывов