Xilinx Virtex-5 FPGA ML561 страница 111 Скачать руководство пользователя | Manualshive

Страница: 111 / 385

background image

Virtex-5 FPGA User Guide

111

UG190 (v5.0) June 19, 2009

PLL in Virtex-4 FPGA PMCD Legacy Mode

PLL in Virtex-4 FPGA PMCD Legacy Mode

Virtex-5 devices do not have Phase-Matched Clock Dividers (PMCDs). The Virtex-5 FPGA
PLL supports the Virtex-4 FPGA PMCD mode of operation. To take advantage of the
inherently more powerful features of the Virtex-5 FPGA PLL, Xilinx recommends
redesigning Virtex-4 FPGA PMCDs by implementing PLLs directly. The difference
between the Virtex-5 FPGA PLL and the Virtex-4 FPGA PMCD block in Virtex-4 FPGA
PMCD legacy mode is that only two clock inputs are supported in the Virtex-5 device
implementation. The Virtex-4 device implementation supported up to four clock inputs. If
four clock inputs must be used, then two PLLs can be put into PMCD mode. In this case,
delay matching is not optimal.

shows the Virtex-4 FPGA PMCD primitive implemented using a PLL. A PLL

can not be used as a PLL if it is already being used as a PMCD. To design-in the Virtex-5
FPGA PMCD functionality, instantiate a Virtex-4 FPGA PMCD primitive. ISE software
maps the Virtex-4 FPGA PMCD primitive into a Virtex-5 FPGA PLL.

shows the port mapping between Virtex-5 FPGA PLL in PMCD legacy mode and

the Virtex-4 FPGA PMCD port names.

X-Ref Target - Figure 3-17

Figure 3-17:

PMCD Primitive Implemented Using the PLL in PMCD Legacy Mode

Table 3-8:

Mapping of Port Names

Virtex-4 FPGA

Port Name

Virtex-5 FPGA

Port Name

CLKA

CLKIN

CLKB

CLKFBIN

CLKC

n/a

CLKD

n/a

CLKA1

CLKOUT3

CLKA1D2

CLKOUT2

CLKA1D4

CLKOUT1

CLKA1D8

CLKOUT0

CLKFBOUT

CLKIN

CLKFBIN

O0

O1

O2

ug190_3_16_022207

O3

To BUFG

«
...
109
110
111
112
113
...
»

Содержание Virtex-5 FPGA ML561


































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Virtex-5 FPGA ML561

Бренд: F5 Страницы: 2

Бренд: F5 Страницы: 90

Бренд: F5 Страницы: 47

Бренд: IEI Technology Страницы: 19

Бренд: IEI Technology Страницы: 87

Бренд: IEI Technology Страницы: 3

Бренд: Orban Страницы: 255

Бренд: SIIG Страницы: 20

Бренд: MC Страницы: 21

Бренд: Caton Страницы: 18

Turbo NAS TVS-71 Series

Бренд: QNAP Страницы: 51

Бренд: Longshine Страницы: 35

Бренд: Aurora Страницы: 6

NVR41-4KS2 Series

Бренд: Dahua Страницы: 452

Бренд: ATI Technologies Страницы: 87

Бренд: Aaeon Страницы: 119

Бренд: Cowlacious Designs Страницы: 8

Бренд: Freescale Semiconductor Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды