manualshive.com logo in svg

Xilinx LogiCORE IP Spartan-6, Руководство по началу работы

Поделиться
Скачать
Xilinx LogiCORE IP Spartan-6 Скачать руководство пользователя страница 42

42

www.xilinx.com

Spartan-6 FPGA GTP Transceiver Wizard v1.8

UG546 (v1.8) December 14, 2010

Chapter 4: 

Quick Start Example Design

Functional Simulation of the Example Design

Using ModelSim

The Spartan-6 FPGA GTP Transceiver Wizard provides a quick way to simulate and 
observe the behavior of the wrapper using the provided example design and script files.

Prior to simulating the wrapper with ModelSim, the functional (gate-level) simulation 
models must be generated. All source files in the following directories must be compiled to 
a single library as shown in 

Table 4-1

. See the 

Synthesis and Simulation Design Guide

 for 

ISE

®

  12.4, available in the ISE

®

 Software Documentation for instructions on how to 

compile ISE simulation libraries.

The Wizard provides a command line script for use within ModelSim. To run a VHDL or 
Verilog ModelSim simulation of the wrapper, use the following instructions:

1.

Launch the Modelsim simulator and set the current directory to

<project_directory>/<component_name>/simulation/functional

2.

Set the MTI_LIBS variable:

modelsim> 

setenv MTI_LIBS <

path to compiled libraries

>

3.

Launch the simulation script:

modelsim> 

do simulate_mti.do

The ModelSim script compiles the example design and test bench, and adds the relevant 
signals to the wave window.

Table 4-1: 

Required ModelSim Simulation Libraries

HDL

Library

Source Directories

Verilog

UNISIMS_VER

<

Xilinx dir

>/spartan6/verilog/src/unisims

 

<

Xilinx dir

>/spartan6/secureip/mti

VHDL

UNISIM

<

Xilinx dir

>/spartan6/vhdl/src/unisims/primitive

 

<

Xilinx dir

>/spartan6/secureip/mti

Содержание LogiCORE IP Spartan-6




















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды