Xilinx LogiCORE IP AXI Скачать руководство пользователя

Страница: 66 / 107

AXI Bridge for PCI Express v2.4

www.xilinx.com

PG055 June 4, 2014

Chapter 4:

Design Flow Steps

For further details, see:

• “Working with IP” and “Customizing IP for the Design” in the

Vivado Design Suite User

Guide: Designing with IP

(UG896)

[Ref 9]

• “Working with the Vivado IDE” section in the

Vivado Design Suite User Guide: Getting

Started

(UG910)

[Ref 8]

Note:

Figures in this chapter are illustrations of the Vivado Integrated Design Environment (IDE).

This layout might vary from the current version.

Customizing the Core

The AXI Bridge for PCI Express core customization parameters are described in the

following sections.

Basic Parameter Settings

The initial customization screen shown in

Figure 4-1

is used to define the basic parameters

for the core, including the component name, reference clock frequency, and silicon type.

X-Ref Target - Figure 4-1

Figure 4-1:

Basic Parameter Settings

Send Feedback

Содержание LogiCORE IP AXI












































































































Результаты поиска

Содержание LogiCORE IP AXI

Отзывы:

Похожие инструкции для LogiCORE IP AXI

Бренды по названию

Популярные бренды

Xilinx LogiCORE IP AXI, Руководство по эксплуатации продукта

Результаты поиска

Содержание LogiCORE IP AXI

Отзывы:

Похожие инструкции для LogiCORE IP AXI

Бренды по названию

Популярные бренды