Xilinx LogiCORE IP AXI Скачать руководство пользователя

Страница: 46 / 107

AXI Bridge for PCI Express v2.4

www.xilinx.com

PG055 June 4, 2014

Chapter 3:

Designing with the Core

TIP:

Sharing the MMCM between PCIe and other cores in your design saves FPGA resources and eases

output clock path routing.

Limitations

• Reference clock input to MMCM is restricted to 100 MHz in most use cases.

There is an option for selecting a reference clock of 125MHz or 250MHz, which is

not a common use case.

• The MMCM reset is tied to a static value in the top module. The MMCM can be reset as

required by the system design. Note that MMCM reset can be asserted only after

reference clock is recovered and is stable. Also, MMCM reset is indirectly tied to the

PCIe core reset and asserting MMCM reset will reset the PCIe core.

• The

userclk1

and

userclk2

outputs are selected based on the

PCIe Lane Width

Link Speed

, and

AXI width

selections (for details, see

Customizing the Core in

Chapter 4

). Sharing cores must comply with these requirements.

Shared GT_COMMON

A quad phase-locked loop (QPLL) in GT_COMMON can serve a quad of GT_CHANNEL

instances. If the PCIe core is configured as X1 or X2 and is using a QPLL, the remaining

GT_CHANNEL instances can be used by other cores by sharing the same QPLL and

GT_COMMON.

To share GT_COMMON instances, select

Include Shared Logic (Transceiver

GT_COMMON) in example design

option in the Shared Logic tab(

Figure 3-4

When this feature is selected, the GT_COMMON instance is removed from the pipe

wrappers and is moved into the support wrapper of the example design. It also brings out

additional ports to the top level to enable sharing of the GT_COMMON.

Shared logic feature for GT_COMMON helps save FPGA resources and also eases dedicated

clock routing within the single GT Quad.

Shared GT_COMMON Use Cases with GTX and GTP

Table 3-1:

Shared GT_COMMON Use Cases

GT – PCIe max Link

Speed

Device – PCIe Max Link Speed

Shared GT_COMMON

GTX

Kintex7, Virtex7 (485T) – PCIe Gen2 PCIe Pipe Wrappers instantiate

GT_COMMON . Shared IP uses QPLL because

PCIe uses CPLL inside GT_CHANNEL

GTP

Artix7 – PCIe Gen2

GTP_COMMON has 2 QPLLs. PCIe Pipe

Wrappers use only one QPLL. The remaining

one can be used by shared IP core.

Send Feedback

Содержание LogiCORE IP AXI












































































































Результаты поиска

Содержание LogiCORE IP AXI

Отзывы:

Похожие инструкции для LogiCORE IP AXI

Бренды по названию

Популярные бренды

Xilinx LogiCORE IP AXI, Руководство по эксплуатации продукта

Результаты поиска

Содержание LogiCORE IP AXI

Отзывы:

Похожие инструкции для LogiCORE IP AXI

Бренды по названию

Популярные бренды