Xilinx DPU IP Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 43

background image

Chapter 5: Development Flow

DPU IP Product Guide

30

PG338 (v1.2) March 26, 2019

Configure DPU Parameters

You can configure the DPU IP as shown in Figure 21. The details about these parameters can be found

in Chapter 3: DPU Configuration.

Figure 21: Configure DPU

Connect DPU with a Processing System in the Xilinx SoC

No matter how many DPU cores are configured, there is only one slave interface in the DPU IP. Each

DPU core has three master interfaces, one for instruction fetch and the other two for data fetch. The

number of master interfaces in the DPU IP depends on the DPU_NUM parameter.
You can connect the DPU to a processing system (PS) with any kind of interconnections. You must

ensure the DPU can correctly access the DDR memory space. Generally, an AXI data transaction passes

an Interconnect IP, the delay of data transaction will increase. The delay of the data transmission

between the DPU and the Interconnect will reduce the DPU performance. Therefore, Xilinx®

recommends that each data fetch master interface in the DPU connects to the PS through a direct

connection rather than through an AXI Interconnect IP. The reference connection between the DPU and

PS in the Xilinx Ult™ MPSoC is shown as Figure 22.

«
...
28
29
30
31
32
...
»

Содержание DPU IP












































Отзывы:

Нет отзывов

Похожие инструкции для DPU IP

Бренд: Paradyne Страницы: 20

Compshere 3000 Series

Бренд: Paradyne Страницы: 2

Бренд: Lanner Страницы: 2

TWR-SB0410-36EVB

Бренд: NXP Semiconductors Страницы: 26

NetStructure ZT 5515

Бренд: Intel Страницы: 90

Бренд: FONESTAR Страницы: 8

Бренд: Lanner Страницы: 78

Бренд: Z3 Technology Страницы: 87

Through Hole Power Inductors 1411

Бренд: Delta Electronics Страницы: 1

Бренд: HighPoint Страницы: 10

ExtremeCloud Appliance E1120

Бренд: Extreme Networks Страницы: 219

Бренд: HighPoint Страницы: 12

Gen3 Ethernet Module

Бренд: NCD Страницы: 18

Бренд: ZALMAN Страницы: 12

Бренд: Martin Страницы: 41

EK-TIM Indigo Extreme

Бренд: ekwb Страницы: 4

BNC-08DI, BNC-16DI, BNC-16SE

Бренд: Omega Engineering Страницы: 25

OFFICEBRIDGE ONLINE

Бренд: Muratec Страницы: 220

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды