Xilinx DPU IP Скачать руководство пользователя страница 11

Страница: 11 / 43

Chapter 2: Product Specification

DPU IP Product Guide

www.xilinx.com

PG338 (v1.2) March 26, 2019

DSP with Enhanced Utilization (DPU_EU)

In the previous DPU version, the general logic and DSP slices work in the same clock domain, though

technically the latter can run at a higher frequency. To enhance the utilization of DSP slices in DPU, the

advanced DPU_EU version was designed.
The EU in “DPU_EU” means enhanced utilization of DSP slices. DSP Double Data Rate (DDR) technique is

used to improve the performance achieved with the device. Therefore, two input clocks for DPU is

needed, one for general logic, and the other for DSP slices. The difference between DPU and DPU_EU is

shown in Figure 7.
All DPU mentioned in this document refer to DPU_EU, unless otherwise specified.

IMG

ram

IMG

ram

WGT

ram

RES

DSP48 Slice

A+D

clk1x

IMG

ram

IMG

ram

WGT

ram

DSP48 Slice

A+D

clk2x

WGT

ram

RES

DLY

RES

OUT

DLY

Async

SEL

PCIN

PCOUT

RES

clk1x

X22333-022019

Figure 7: Difference between DPU and DPU_EU

Port Descriptions

The DPU top-level interfaces are shown in the following figure.

Figure 8: DPU_EU IP Port

Send Feedback

Содержание DPU IP












































Результаты поиска

Содержание DPU IP

Отзывы:

Похожие инструкции для DPU IP

Бренды по названию

Популярные бренды

Xilinx DPU IP, Руководство по эксплуатации продукта

Результаты поиска

Содержание DPU IP

Отзывы:

Похожие инструкции для DPU IP

Бренды по названию

Популярные бренды