manualshive.com logo in svg

Xhorse CONDOR XC-007, Руководство пользователя, Страница: 3 / 31

Поделиться
Скачать
Xhorse CONDOR XC-007 Скачать руководство пользователя страница 3

Automatic  Key  Cutting  Machine

  - 

CONDOR  XC-007

 

         

                                         

 

3

 

1

．Safety Precautions and Warnings 

To prevent personal injury or damage to machine, read this instruction manual first 

and observe the following safety precautions: 

 

 

Always work on machine in a safe environment. 

 

Wear safety eye protection that meets ANSI standards. 

 

Keep protection mask closed when machine is working. 

 

Keep clothing, hair, hands, tools, test equipment, etc. away from all moving 

parts. 

 

Keep an eye on machine when machine work, do not far from machine. 

 

Do not use damage or loosen power cord. 

 

Unplug the power cord when not in use for a long time. 

 

Do not place machine in wet, oily, dusty area. 

 

Do not place any tool, container on the machine. 

 

Place the machine on a level and firm surface. 

 

Keep the machine clean and dry. 

 

Turn off the power immediately when any exception occurs. 

 

 

 

 

 

Содержание CONDOR XC-007
































Отзывы:

Нет отзывов