get a document from the user and contact support for help. 003-942 Untrusted BSD-ON document format: - Untrusted
document format detected. Cause/Action 1. Click [Stop] in the user interface area. 2. Check the document size group
setting. 3. Check the document size. 4. If the document format is supported, DADF may not work properly.
To check the DADF, see this FIP. • 005-196 (Stuck due to SS size mismatch in unmixed format) • 005-948 (Stuck due to
SS size mismatch blocking insoluble size) Cause/Action Click [Stop] on the UI panel and change the settings. 003-972
EPC memory full BSD-ON: - EPC memory full during copy. Cause/Action Print all images that have been successfully
scanned by the DADF so far, then copy again to find the documents (images) that failed to be scanned. 003-973 NG
Autorotate outside BSD-ON range: - The following conditions were met during copying. • Rotation required. • At
document reduction/enlargement ratio X, the resulting image is larger than 297 mm. Cause/Action Click the [Stop]
button on the user interface and change the reduction/enlargement ratio. First Edition 08/2012 RAP Status Screen 003-
500/795, 003-951 WorkCentre 5021/5019 2-9 RAP Status Screen 08/2012 Initial Edition 003-500/795, 002-951
WorkCentreeRAP 08/2012 First edition 004-345 2-12 Worcentre 5021/5019 005-122 Dadf Simplex Senzer Initial
Record/1. Page BSD-on: CH5.4 • When the first sheet of paper (DADF) begins, serve the engine running (clockwise) in
the initial registration sensor in one-sided and double-sided mode, which does not turn at the specified time.
• Starting with the second sheet pre -feed (the Dadf motor is on (clockwise)) in a double mode, the preliminary
registration sensor does not turn on the specified time. 005-125/145 DADF recording sensor locked/recording DADF
sensor is disabled. Reverse locked BSD-on: CH5.5, CH5.4 [Dadf recording sensor) When the DADF pre-recording sensor
was turned off during the scan, the Dadf recording sensor did not turn off within the specified time. Cause/Action Check
the following: • Transport error caused by foreign bodies on the document track. • The surface of the feed cylinder and
pressure cylinder is free of foreign bodies.
• Check the surface wear and pressure roller surface. • Initial PADF Registration Sensor (Check Input [005-206]) to not
work incorrectly. (PL 56.14) • Dadf Food Clutch escapes (output management [005-062]). (PL 56.7) • Dadf motor (check
output [005-008]) to detect unusual operation. (PL 56.6) • Wear and damage wheel. If you have no problem, replace the
DADF card. (PL 56.2) 005-123 Simplex/Side 1 blocked Dadf recording sensor. BSD-on: CH5.5, CH5.4 Preliminary
recording sensor Dadf will not switch to preliminary recording sensor at the specified time. [The Dadf Recording Sensor
stuck in the reverse] after the reverse mode was turned off in the reverse mode, the DadF recording sensor did not turn
off within the specified time. Cause/Action Check the following: • Transport error caused by foreign bodies on the
document track.
• There are no foreign bodies on the surface of the registration cylinder, output cylinder and output cylinder. • The
surface of the registration cylinder, output cylinder and output cylinder is worn. • DADF recording sensor (select input
[005-110]) malfunction. (PL 56.14) • DADF Preliminary Registration Sensor (Entrance Management [005-206])Pre-
cooking sensor (input test [005-206]) in operational errors. (PL 56.14) ¢ DADF T/A Sooling (Initial Test [005-098]) in
Corporate Bankruptcy. (PL 56.7) â € â° DADF Engine Power Piews Supply (Output Test [005-008]) for operation failure.
(PL 56.6) MBERS Tax Union. If no problem occurs, replace the DADF conductor plate. (PL 56.2) 005-131/ 132 DADF
return sensor for connection with DADF return sensor for BSD-ON connection: CH5.5, CH5.4. Rear [Rear DADF
Sensor] After the Regue DADF sensor was turned on during the scanning process, the rear father sensor did not load at
the specified hour. Checking cause/solutions: Mbers transports errors due to foreign bodies in the document path.
Original edition 08/2012 View state rap 005-122, 005-125/145 WorkCentre 5021/5019 2-13 Be sure to check for wear. •
DADF return sensor (entry test [005-211]) for fault. (PL 56.10) â ALC DADF sensor (input test [005-110]) for operational
errors. (PL 56.14) ††(PL 56.6) MBERS Tax Union. If no problem occurs, replace the DADF conductor plate. ) Time
cannot be deactivated.
[DADF Reverse Reversal Sensor]. During simple and duplex scanning, the DADF reverse sensor did not come out for an
indefinite amount of time after the DADF Regi sensor was turned off. Checking cause/solutions: Mbers transports errors
due to foreign bodies in the document path. • SurfaceIf no problems are found, replace the DADF PCB. (PL 56.2) 005-
135 DADF 2 Side preregistration sensor stuck in BSD-ON: CH5.4, CH5.5 DADF power motor starts in reverse mode,
DADF no-show sensor did not turn on. allotted time.
Cause/Action: Check the following: • Interruption of transportation due to foreign objects on the road.
• There are no foreign substances on the surface of the cylinder. • Cylinder exit surface due to wear and vacuum (PL
56.14) • DADF feed motor (exit test [005-048]) due to action failure.
(PL 56.6) • Compression cylinder in case of failure (including outlet air gap for relief in case of magneto failures (initial
test [005-072]))). (PL 56.7) • Voyage of devaluation and damage. If no problems are found, replace the DADF PCB. (PL
56.2) 005-136 DADF SONG SENSOR 2 SENSOR LOCKED IN BSD-ON: CH5.5, CH5.4 After the DaDF pre-recording
sensor was turned on under the influence, the Dadf region sensor did not pass the specified time. Cause/Action: Check
the following: • Interruption of transportation due to foreign objects on the road. • Exit roller, pickup roller and surface
for foreign particles. • Check the wear of the exit roller, roller and adjustment roller. • DADF register sensor (input
control [005-110]) due to action error. (PL 56.14) • DADF preregistration sensor (input control [005-206]) due to action
error. (PL 56.14) • DADF power motor (output control [005-008]) due to action error. (PL 56.6) • DADF T/A clutch (test
output [005-098]) due to action error. (PL 56.7) • Output cylinder failure (including output gap release solenoid failure
(Output Inspection [005-072])). (PL 56.7) • Voyage of devaluation and damage.
If no problems are found, replace the DADF PCB. (PL 56.2) Status display RAP 08/2012 first edition 005-131/132, 005-
135 2-14 WorkCentre 5021/5019 0If the operation fails. (PL 56.14) - Dadf power supply (005-048/008] (CCW/CW)
accident. (PL 56.6) • Failure output role (including PIN block failure (exit [005-072]). (PL 56.7) • gear trip from wear. If
there is no problem, replace Dadf PWB. (PL 56.2) 005 -196 Molom Molosoma Melic Melic Melic BSD-on: CH5.4, CH5.2.
It has been found that 2 or the next pages are different, which is not applicable to 1 page (page 2 or more) SS is longer
direction longer). Cause / Action 1.
Check the size of the user document. 2. If the error is not removed, check the following: Causes / Operation to the user
explain that mixed dimensions are not supported. 005-198/ 199 Strigtis too short/ too long jem BSD-on: CH5.4, CH5.2
[stuck too short 85 mm, double sided: 110 mm). [Stuck for too long] discovered that the length of the document in the
direction of slow scan corresponds to the specifications (Simpex: 1275 mm, double chapter: 480.1 mm) or more. Cause /
Action Check the size of the user document. If the DADF transport length is not exceeded, check: (PL 56.14) ° Fate size
1/2 (Entrance Check [005-221/222]) In case of failure.
(PL 56.11) If there is no problem, replace Dadf PWB. (PL 56.2) 005-210 DADF Download Do BSD-on: CH3.1 starts IIS
(including energy restoration / sleep), Dadf is found in boot mode. • Dadf Pre Antine sensor (input test [005-206])
failure. (PL 56.14) ° Fate size 1/2 (Entrance Check [005-221/222]) In case of failure. (PL 56.11) 3. If the problems are
not found, replace Dadf PWB. (PL 56.2) Cause / Action performed by DPapa Pwb. (PL 56.2) 005-305 TAF block open