Xerox EX 570 Скачать руководство пользователя | Manualshive

Страница: 7 / 61

background image

I

NTRODUCTION

7

I

NTRODUCTION

This document is intended for administrators of the Xerox

®

EX 570 Print Server Powered by

Fiery

®

/ Xerox

®

EXi 570 Print Server Powered by Fiery

®

, which is referred to in this document

as the EX/i Print Server.

This document primarily describes tasks that must be completed or coordinated by the
administrator before the EX/i Print Server is ready for use. It assumes that the EX/i Print
Server has been unpacked from its shipping container and that all required cables are
connected from the EX/i Print Server to the network, a power source, and the printer, and
that the printer is operational.

If you are an administrator and plan to configure a EX/i Print Server, it is strongly
recommended that you carefully review this entire document, beginning with

installation on the network”

About this document

This document includes information about the following:

•

System Requirements

•

Setting up from the Printer Touch Panel

•

Setting up from a Client Computer

•

Setup Option Reference

•

•

Back up and Restore Settings

•

•

Troubleshooting

«
...
5
6
7
8
9
...
»

Содержание EX 570






























































Отзывы:

Нет отзывов

Похожие инструкции для EX 570

Бренд: Oki Страницы: 282

Бренд: Samsung Страницы: 82

Бренд: Samsung Страницы: 2

Бренд: Xerox Страницы: 108

Бренд: Unimark Страницы: 38

Бренд: Citizen Страницы: 80

Бренд: MSI Страницы: 107

Бренд: IBM Страницы: 106

Бренд: Protech Systems Страницы: 140

FusionServer G5500 V6

Бренд: xFusion Digital Technologies Страницы: 100

Бренд: Patton Страницы: 15

Бренд: Eneo Страницы: 94

SUPERSERVER 1018D-73MTF

Бренд: Supero Страницы: 124

Бренд: PRG Страницы: 50

totalstorage fastt100

Бренд: IBM Страницы: 160

Бренд: NEC Страницы: 10

AcquiLite A7810-0

Бренд: Obvius, LLC Страницы: 29

Бренд: Ice Страницы: 114

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды