Xerox DocuColor 2240 Скачать руководство пользователя страница 129

Страница: 129 / 1489

09/03

2-96

DC 3535/2240/1632, WC M24

5-703

Initial issue

Status Indicator RAPs

5-703 DADF Belt Motor RAP

Use this RAP when directed to troubleshoot problems with the DADF Belt Motor.

Initial Actions

Remove the following:

•

Front Cover (

PL 20.1

)

•

Entrance Tray (

PL 20.1

)

•

Lower Chute Assembly (

REP 5.8

)

•

Rear Cover (

REP 5.18

)

Procedure

Switch off the power and manually move the Platen Belt (

PL 20.10

The Platen Belt moves

freely.
Y

Look for binding in the DADF Platen Belt and the drives for the DADF Belt Motor. Correct
any problems

Check Fuse F1 on the DADF Control PWB.

The Fuse is good.

Replace the Fuse. If the Fuse blows again, go to

Flag 1

Flag 2

, and

Flag 3

. Check the

wires for a short circuit to ground. If the wires are good, replace the DADF Belt Motor (

20.6

). If the problem continues, replace the DADF Control PWB (

PL 20.3

+24 VDC is measure at

P/J595

-1 on the DADF Control PWB.

N
+24 VDC is measured at

P/J594

-2 on the DADF Control PWB.

N
+24 VDC is measured at

P/J594

-1 on the DADF Control PWB.

Replace the DADF Control PWB (

PL 20.3

Go to

Flag 1

and

Flag 2

. Check the wires for an open circuit. If the wires are good,

replace the DADF Interlock Switch (

PL 20.3

Replace the DADF Control PWB (

PL 20.3

NOTE: In the following step, one of the pins on

P/J595

will measure less than +24 VDC. This

is normal operation.

+24 VDC is measured at three of the following pins:

P/J595

-2, 3, 4, or 5.

Go to

Flag 3

and

Flag 4

. Check the wires for an open circuit. If the wires are good, replace

the DADF Belt Motor (

PL 20.6

Replace the DADF Belt Motor (

PL 20.6

). If the problem continues, replace the DADF Control

PWB (

PL 20.3

Figure 1 5-703 RAP Circuit Diagram - Belt Motor

Содержание DocuColor 2240


















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание DocuColor 2240

Отзывы:

Похожие инструкции для DocuColor 2240

Бренды по названию

Популярные бренды

Xerox DocuColor 2240, Руководство по обслуживанию

Результаты поиска

Содержание DocuColor 2240

Отзывы:

Похожие инструкции для DocuColor 2240

Бренды по названию

Популярные бренды