manualshive.com logo in svg

Xerox 2135N - Phaser Color Laser Printer, Краткое руководство пользователя

Поделиться
Скачать
Xerox 2135N - Phaser Color Laser Printer Скачать руководство пользователя страница 157

144

Phaser 2135 Color Printer

Xerographic components

Shutter plate

Warning

Switch off the power and disconnect the power cord.

1.

Open the top cover.  Remove the drum/toner cartridges.  Place them in  
a lightproof black bag to protect the drum units from light and store in a 
safe place.

2.

Remove the transfer belt unit as explained on page 124.

3.

Through the opening in the shutter plate, carefully remove the shutter 
spring.

4.

Open the shutter plate to the full open position.

5.

Carefully lift the tabs on the front edge of the shutter plate over the 
stopper and continue to move it toward the front.

6.

Remove the shutter plate.

Reverse these steps to install the shutter plate; ensure all guide pins on the shutter 
plate are properly aligned when reinstalling.  Move the shutter plate to the full 
closed position to insert the shutter spring.  

Removing the shutter plate

Shutter Spring 

Tabs

0725-49

Содержание 2135N - Phaser Color Laser Printer








































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды