xenium X-DSP Скачать руководство пользователя страница 18

18

SAFETY INSTRUCTIONS

THE PURCHASED DEVICE IS ONLY SUITABLE FOR AN OPERATION 

WITH A 12V ON-BOARD ELECTRICAL SYSTEM OF A VEHICLE.

 Other-

wise fire hazard, risk of injury and electric shock consists.

PLEASE DO NOT MAKE ANY OPERATION OF THE SOUND SYSTEM, 

WHICH DISTRACT YOU FROM A SAFE DRIVING. 

Do not make any pro-

cedures, which demand a longer attention. Perform these operations not 

until you have stopped the vehicle on a safe place. Otherwise the risk of 

accident consists. 

ADJUST THE SOUND VOLUME TO AN APPROPRIATE LEVEL, THAT 

YOU ARE STILL ABLE TO HEAR EXTERIOR NOISES WHILE DRIVING. 

High performance sound systems in vehicles may generate the acoustic 

pressure of a live concert. The permanent listening to extreme loud music 

may cause the loss of your hearing abilities. The hearing of extreme loud 

music while driving may derogate your cognition of warning signals in the 

traffic. In the interests of the common safeness, we suggest to drive with a 

lower sound volume. Otherwise the risk of accident consists.   

DO NOT COVER COOLING VENTS AND HEAT SINKS.

 Otherwise this 

may cause heat accumulation in the device and fire hazard consists.

DO NOT OPEN THE DEVICE.

  Otherwise  fire  hazard,  risk  of  injury  and 

electric shock consists. Also this may cause a loss of the warranty. 

REPLACE FUSES ONLY WITH FUSE WITH THE SAME RATING.

 Other-

wise fire hazard and risk of electric shock consists.

DO NOT USE THE DEVICE ANY LONGER, IF A MALFUNCTION, WHICH 

REMAINS UNREMEDIED.

  Refer  in  this  case  to  the  chapter  TROUBLE 

SHOOTING. Otherwise risk of injury and the damage of the device con-

sists. Commit the device to an authorized retailer. 

INTERCONNECTION AND INSTALLATION SHOULD BE ACCOM-

PLISHED BY SKILLED STAFF ONLY. 

The interconnection and installation 

of this device demands technical aptitude and experience. For your own 

safeness, commit the interconnection and installation to your car audio re-

tailer, where you have purchased the device.  

DISCONNECT THE GROUND CONNECTION FROM THE VEHICLE’S 

BATTERY BEFORE INSTALLATION.

 Before you start with the installation 

of the sound system, disconnect by any means the ground supply wire from 

the battery, to avoid any risk of electric shock and short circuits.

CHOOSE AN APPROPRIATE LOCATION FOR THE INSTALLATION OF 

THE DEVICE. 

Look for an appropriate location for the device, which en-

sures a sufficient air circulation. The best places are spare wheel cavities, 

and open spaces in the trunk area. Less suitable are storage spaces behind 

the side coverings or under the car seats. 

DO NOT INSTALL THE DEVICE AT LOCATIONS, WHERE IT WILL BE 

EXPOSED TO HIGH HUMIDITY AND DUST.

 Install the device at a loca-

tion, where it will be protected from high humidity and dust. If humidity and 

dust attain inside the device, malfunctions may be caused. 

MOUNT THE DEVICE AND OTHER COMPONENTS OF THE SOUND 

SYSTEM SUFFICIENTLY. 

Otherwise the device and components may get 

loose and act as dangerous objects, which could cause serious harm and 

damages in the passenger room.  

ENSURE NOT TO DAMAGE COMPONENTS, WIRES AND CABLES OF 

THE VEHICLE WHEN YOU DRILL THE MOUNTING HOLES. 

If you drill 

the mounting holes for the installation into the vehicle’s chassis, ensure by 

any means, not to damage, block or tangent the fuel pipe, the gas tank, 

other wires or electrical cables. 

ENSURE CORRECT CONNECTION OF ALL TERMINALS.

  Faulty  con-

nections may could cause fire hazard and lead to damages of the device.

DO NOT INSTALL AUDIO CABLES AND POWER SUPPLY WIRES TO-

GETHER.

 Ensure while installation not to lead the audio cables between 

the head unit and the processor together with the power supply wires on the 

same side of the vehicle. The best is a areal separated installation in the left 

and right cable channel of the vehicle. Therewith a overlap of interferences 

on the audio signal will be avoided. This stands also for the equipped bass-

remote wire, which should be installed not together with the power supply 

wires, but rather with the audio signal cables.    

ENSURE THAT CABLES MAY NOT CAUGHT UP IN CLOSE-BY OB-

JECTS.

 Install all the wires and cables like described on the following pag-

es, therewith these may not hinder the driver. Cables and wires which are 

installed close-by the steering wheel, gear lever or the brake pedal, may 

caught up and cause highly dangerous situations.  

DO NOT SPLICE ELECTRICAL WIRES. 

The electrical wires should not be 

bared, to provide power supply to other devices. Otherwise the load capac-

ity of the wire may get overloaded.  Use therefor a appropriate distribution 

block. Otherwise fire hazard and risk of electric shock consists.

DO NOT USE BOLTS AND SCREW NUTS OF THE BRAKE SYSTEM 

AS GROUND POINT.

  Never  use  for  the  installation  or  the  ground  point 

bolts and screw-nuts of the brake system, steering system or other security-

relevant components. Otherwise fire hazard consists or the driving safety 

will be derogated.  

ENSURE NOT TO BEND OR SQUEEZE CABLES AND WIRES BY 

SHARP OBJECTS.

 Do not install cables and wires not close-by movable 

objects like the seat rail or may be bent or harmed by sharp and barbed 

edges. If you lead a wire or cable through  the hole in a metal sheet, protect 

the insulation with a rubber grommet. 

KEEP AWAY SMALL PARTS AND JACKS FROM CHILDREN.

 If objects 

like these will be swallowed, the risk of serious injuries consists. Consult 

promptly a medical doctor, if a child swallowed a small object. 

PLEASE NOTE THE FOLLOWING ADVICE BEFORE THE FIRST OPERATION!

Содержание X-DSP

































Отзывы: