background image

DO NOT RETURN TO RETAILER WHERE YOU PURCHASED AT.

CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or [email protected]

3

PLAY SUPERVISION

DO NOT

allow more than one child to play on the individual swing or slide component at any one time.

DO NOT

allow children to stand on the slide, swing seats, trapeze, seesaw, rocky rider, disc swing or glide

ride. The glide ride and seesaw are made for only two users at a time. The disc swing & rocky rider are
made for one or two users at a time.

DO NOT

allow children to walk too close to moving parts.

ALWAYS

keep a safe distance to avoid being

struck by other children while playing on swings, slides, disc swing and glide ride etc.

DO NOT

swing empty seats as this may cause injuries.

ALWAYS

guide children to sit in the center of swinging parts, with their full weight placed in the seat center

and holding on to the swing chains.

DO NOT

allow children to jump off the equipment while it is in motion.

ALWAYS

come to a full stop before

dismounting.

ALWAYS

dress children appropriately for proper play, e.g. wear well-fitted rubber sole shoes, and remove

loose or sharp items such as jewelry, hair accessories, scarves which may become entangled in the
equipment or cause injuries.

ALWAYS

make sure children remove their bike or other sports helmets before playing on the playground.

DO NOT

allow children to slide down the slide head first.

DO NOT

allow children to climb onto swing or jump to/from different play areas of the equipment.

ALWAYS

return safely to the ground before approaching another play area.

DO NOT

allow children to climb on structural parts (e.g. legs, top bar).

These are structural components

and are not designed for play.

ALWAYS

check the slide or other parts exposed to the body for extreme heat from the sun before allowing

children to use the equipment.

ALWAYS

prevent access and secure from any unauthorized use when there is no adult supervision.

DO NOT

allow pets or other animals near the equipment to prevent damage or injuries.

Adequate overhead clearance is essential. A minimum of 24 ft (7.3 meters) from ground level is
recommended. Provide clearance for wires, tree limbs and other possible hazards.

Use the swing set in a well-lit area. Artificial illumination may be required for shady areas.

DO NOT

allow children to twist the swing chains or loop them over the

top support bar as this may reduce the strength of the chain. Twisting
may break the chain and causing danger to children.

Содержание 74520SF











































Отзывы: