manualshive.com logo in svg

XCMG XZ320, Руководство по эксплуатации

Поделиться
Скачать
XCMG XZ320 Скачать руководство пользователя страница 40

Manual of XZ320 Horizontal Directional Drill

 

37 

3.3.3 Close clamp switch of holder. 

3.3.4 Rotate the lifting device to move the auger stem to its axle. 

3.3.5 Lubricate front threads of auger stem. 

Note

：

Thread oil shall be brushed on threads of auger stem and short 

connector when installing the auger stem.

 

3.4 Connect the auger stem. 

3.4.1 Power head shall be pushed forward until main axle thread contacts 
auger stem. 

3.4.2 Continue to push power and rotate main axle until main axle thread is 
installed on the auger stem. 

3.4.3 Power head shall move forward slowly until new auger stem contacts 
front auger stem threads. 

3.4.2 Push the power head and rotate the main axle until new auger stem 
is tightened with front auger stem. 

3.4.3 Loosen the front jaw vice. 

3.4.4 Press the holder switch then open the holder. 

3.4.5 Rotate lifting device switch for declination. 

Note

：

Be sure that lifting device of auger stem is in the lowest position 

before pushing power head forward. Guarantee sufficient free motion 
distance between power head and carriage during loading/unloading 
of auger stem.

 

3.5  Pressure the charging  mud  pump  switch so that  auger  stem  is  full of 
mud with increased mud pressure. 

Note

：

Adjust  speed  control  handle  of  mud  pump  and  set  pressure 

suitably. Gear can not be changed during operation of mud pump. 

Gear  variation  operation  of  mud  pump:  It  is  the  easiest  to  change  gears 
within 10 seconds after closing the mud pump because transmission gear 
is still in operation. 

Please refer to operation manual of mud pump for operation. 

3.6  Rotate  the  main  axle  and  drill  slowly  then  adjust  rotation  speed 

according to dimension of drill bit and soil conditions. 

Attention

：

  Be  sure  to  rotate  it  clockwise  unless  connector  of 

auger  stem  is  cut  off.  Connector  will  be  loosened  by 
counter-clockwise rotation.

 

top-stm.ru

Содержание XZ320


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды